Dell 3200MP Content: Dell 3200MP Projector User's Guide - Page 12

Do Not Unplug The Projector Before Properly Shutting Down Using The Following Steps. - replacement lamp

Get Dell 3200MP - XGA DLP Projector PDF manuals and user guides View all Dell 3200MP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

1 Power button 2 Lens cap Powering Off the Projector DO NOT UNPLUG THE PROJECTOR BEFORE PROPERLY SHUTTING DOWN USING THE FOLLOWING STEPS. 1. Press the power button to turn off the projector. The "Power Off the Lamp?" message appears on the OSD. 2. Press the power button again. The cooling fans continue to operate for 2 minutes. 3. If the LAMP light is solid orange, replace the lamp. 4. If the TEMP light is solid orange, the projector has overheated. The display automatically shuts down. Try turning the display on again after the projector cools down. If the problem persists, contact Dell. 5. If the TEMP light is blinking orange, a projector fan has failed and the projector will automatically shut down, If this problem persists, contact Dell. 6. Disconnect the power cord from the electrical outlet and the projector. 7. If you press the power button while the projector is running, the "Power Off the Lamp?" message appears on the screen. To clear the message, press any button on the control panel or ignore the message; the message will disappear after 5 seconds. Adjusting the Projected Image Adjusting the Projector Height To raise the projector: 1. Press the elevator button. 2. Raise the projector to the desired display angle, and then release the button to lock the elevator foot into position. 3. Use the tilt adjustment wheel to fine-tune the display angle. To lower the projector: 1. Press the elevator button. 2. Lower the projector, and then release the button to lock the elevator foot into position.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
1
Power button
2
Lens cap
Powering Off the Projector
DO NOT UNPLUG THE PROJECTOR BEFORE PROPERLY SHUTTING DOWN USING THE FOLLOWING STEPS.
1. Press the power button to turn off the projector. The
"Power Off the Lamp?"
message appears on the
OSD.
2. Press the power button again. The cooling fans continue to operate for 2 minutes.
3. If the
LAMP
light is solid orange, replace the lamp.
4. If the
TEMP
light is solid orange, the projector has overheated. The display automatically shuts down. Try
turning the display on again after the projector cools down. If the problem persists,
contact Dell
.
5. If the
TEMP
light is blinking orange, a projector fan has failed and the projector will automatically shut down, If
this problem persists,
contact Dell
.
6. Disconnect the power cord from the electrical outlet and the projector.
7. If you press the power button while the projector is running, the
"Power Off the Lamp?"
message
appears on the screen. To clear the message, press any button on the control panel or ignore the message;
the message will disappear after 5 seconds.
Adjusting the Projected Image
Adjusting the Projector Height
To raise the projector:
1. Press the elevator button.
2. Raise the projector to the desired display angle, and then release the button to lock the elevator foot into
position.
3. Use the tilt adjustment wheel to fine-tune the display angle.
To lower the projector:
1. Press the elevator button.
2. Lower the projector, and then release the button to lock the elevator foot into position.