Dell 3200MP Content: Dell 3200MP Projector User's Guide - Page 14

Adjusting Projection Image Size, Changing the Lamp, CAUTION, Lamp Changing Procedure, Reset - problem

Get Dell 3200MP - XGA DLP Projector PDF manuals and user guides View all Dell 3200MP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

2 Focus ring Adjusting Projection Image Size Screen Max (Diagonal) Min. 29.7" 24.8" 82.5" 68.8" 135.2" 112.7" 187.2" 156.0" 240.0" 200.0" 292.8" 244.0" Screen Size Max. (WXH) 23.8"X17.8 66.0"X49.5" 108.2"X81.1" 149.8"X112.3" 192.0"X144.0" 234.2"X175.7" Min. (WXH) 19.8X14.9" 55.0"X41.3" 90.1"X67.6" 124.8"X93.6" 160.0"X120.0" 195.2"X146.4" Distance 4.0' 11.1' 18.2' 25.2' 32.3' 39.4' * This graph is for user reference only. Changing the Lamp Replace the lamp when you see " Lamp is approaching the end of its useful life. Replacement suggested!" message on the screen by carefully following these instructions. If this problem persists, contact Dell. CAUTION: The lamp becomes very hot with use. Do not attempt to replace the lamp after use until the projector has been allowed to cool down for at least 30 minutes. Lamp Changing Procedure: 1. Turn off the projector and disconnect the power cord. 2. Let the projector cool for at least 30 minutes. 3. Lossen the two screws that secure the lamp cover, and remove the cover. 4. Remove the two screws that secure the lamp. 5. Pull up the lamp by its metal handle. 6. Reverse steps 1 through 5 to install the new lamp. 7. Reset the lamp by selecting the left Lamp Reset icon in the OSD Management tab. 8. Dell may require that lamps replaced under warranty are returned to Dell. Otherwise, contact your local waste disposal agency for the address of the nearest deposit site

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
2
Focus ring
Adjusting Projection Image Size
Screen
(Diagonal)
Max
29.7"
82.5"
135.2"
187.2"
240.0"
292.8"
Min.
24.8"
68.8"
112.7"
156.0"
200.0"
244.0"
Screen
Size
Max.
(WXH)
23.8"X17.8 66.0"X49.5" 108.2"X81.1" 149.8"X112.3" 192.0"X144.0" 234.2"X175.7"
Min.
(WXH)
19.8X14.9" 55.0"X41.3" 90.1"X67.6"
124.8"X93.6" 160.0"X120.0" 195.2"X146.4"
Distance
4.0'
11.1'
18.2'
25.2'
32.3'
39.4'
*
This graph is for user reference only.
Changing the Lamp
Replace the lamp when you see
"
Lamp is approaching the end of its useful life.
Replacement suggested!
" message on the screen by carefully following these instructions. If this
problem persists,
contact Dell
.
CAUTION:
The lamp becomes very hot with use. Do not attempt to replace the lamp after use until the
projector has been allowed to cool down for at least 30 minutes.
Lamp Changing Procedure:
1. Turn off the projector and disconnect the
power cord.
2. Let the projector cool for at least 30
minutes.
3. Lossen the two screws that secure the
lamp cover, and remove the cover.
4. Remove the two screws that secure the
lamp.
5. Pull up the lamp by its metal handle.
6. Reverse steps 1 through 5 to install the
new lamp.
7. Reset the lamp by selecting the left
Lamp
Reset
icon in the OSD
Management
tab.
8. Dell may require that lamps replaced under
warranty are returned to Dell. Otherwise,
contact your local waste disposal agency for
the address of the nearest deposit site