Dell Alienware 13 R3 Service Manual - Page 82

Replacing the display bezel, Procedure, Post-requisites

Get Dell Alienware 13 R3 PDF manuals and user guides View all Dell Alienware 13 R3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

Replacing the display bezel WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure 1 Place the display assembly on a clean and flat surface. 2 Connect the logo-board cable to the logo board. 3 Adhere the tape that secures the logo-board cable to the logo board. 4 Slide the alien head logo-board cable into the logo board and close the latch to secure the cable. 5 Carefully turn the display bezel over. 6 Align the display bezel with the display back-cover and antenna assembly and gently snap the display bezel into place. Post-requisites 1 Replace the display assembly. 2 Replace the system board. 3 Replace the heat-sink assembly. 4 Replace the battery. 5 Replace the coin-cell battery. 6 Replace the computer base. 7 Replace the rear-I/O cover. 8 Replace the memory modules. 9 Replace the solid-state drive. 10 Replace the wireless card. 11 Replace the base cover. 82

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
Replacing the display bezel
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in
Before working inside your computer
. After working inside your
computer, follow the instructions in
After working inside your computer
.
For more safety best practices, see the Regulatory Compliance home
page at
www.dell.com/regulatory_compliance
.
Procedure
1
Place the display assembly on a clean and flat surface.
2
Connect the logo-board cable to the logo board.
3
Adhere the tape that secures the logo-board cable to the logo board.
4
Slide the alien head logo-board cable into the logo board and close the latch
to secure the cable.
5
Carefully turn the display bezel over.
6
Align the display bezel with the display back-cover and antenna assembly
and gently snap the display bezel into place.
Post-requisites
1
Replace the
display assembly
.
2
Replace the
system board
.
3
Replace the
heat-sink assembly
.
4
Replace the
battery
.
5
Replace the
coin-cell battery
.
6
Replace the
computer base
.
7
Replace the
rear-I/O cover
.
8
Replace the
memory modules
.
9
Replace the
solid-state drive
.
10
Replace the
wireless card
.
11
Replace the
base cover
.
82