Dell Latitude CPi A User Manual - Page 36

Modular Bay Devices (Diskette Drive, CDROMDrive, Battery, or Travel Module), Audio Shield

Get Dell Latitude CPi A PDF manuals and user guides View all Dell Latitude CPi A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

latch lock NOTE: You do not need to remove the main battery or hard-disk drive prior to this procedure. 1. Close the display and turn the computer over. 2. Remove the device from the modular bay. Push the modular bay latch away from the center of the computer. Keep holding the latch open while pulling the device out of the modular bay with the other hand. 1. Remove the back cover assembly. 2. Remove the keyboard assembly. 3. Remove the palmrest assembly. 4. Remove the 5-mm screw securing the audio shield (see Figure 22). 5. Remove the 5-mm screw securing the EMI drain wire. 6. Remove the audio shield. NOTE: When you replace the audio shield, ensure that the audio shield is properly seated to prevent it from cutting into the speaker wires or interfering with devices installed in the modular bay. (You can check this by temporarily installing a device in the modular bay prior to reinstalling the palmrest assembly.) 30 Dell Latitude CPi A Service Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
30
Dell Latitude CPi A Service Manual
ÂôÄÀ²³ºÇ²Áº¶¼»·È¼¸º%¶·¸¹¼Êʼº¶³·»¼&º
Ŷµ'( ¶³·»¼&ºÇ²Êʼ³Á&ºÃ³ºË³²»¼ÀºÂôÄÀ¼)ººººººº
±²³´µ¶·Â¸¹··Ã»!´ÉÁµ·ÄÁÅ·$¶Ë²Î¶·Ê¶¼»ËÁÉ···
NOTE: You do not need to remove the main battery or hard-disk drive prior to this
procedure.
±²³´µ¶·¸ #½$¿ ÀË¿ ¾Á¿ ÈÄÂ$ ÀËÂɽ¼¿ ¹À ¼Å¿½º ¾Ä ÿ̿º¾ À¼Â½¾¼Á¹ºÇ
¾Á¿ ¼ÄÆÃ˾¿Â ¼ÄÌ¿ÂÎ
1.
Close the display and turn the computer over.
2.
Remove the device from the modular bay.
Push the modular bay latch away from the center of the computer. Keep
holding the latch open while pulling the device out of the modular bay with
the other hand.
½Ä´·Ãº*Ì·¼À´
²
1.
Remove the back cover assembly.
2.
Remove the keyboard assembly.
3.
Remove the palmrest assembly.
4.
Remove the 5-mm screw securing the audio shield (see Figure 22).
5.
Remove the 5-mm screw securing the EMI drain wire.
6.
Remove the audio shield.
NOTE: When you replace the audio shield, ensure that the audio shield is
properly seated to prevent it from cutting into the speaker wires or interfering
with devices installed in the modular bay. (You can check this by temporarily
installing a device in the modular bay prior to reinstalling the palmrest assembly.)
latch lock