Dell OptiPlex GX260 Service Manual - Page 92

Removing a Serial Port Adapter, Removing an AGP or DVI Adapter Card, Filler Bracket Removal

Get Dell OptiPlex GX260 PDF manuals and user guides View all Dell OptiPlex GX260 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

1 card cage 2 serial adapter cable 3 serial adapter system board connector (SER2) Removing a Serial Port Adapter CAUTION: Before you perform this procedure, see "Precautionary Measures." 1. Remove the card cage (see step 1 in "Removing a PCI Card"). 2. Press the lever on the retention arm and raise the retention arm. 3. Lift and remove the adapter bracket. 4. If you are removing the card permanently, install a filler bracket in the empty card-slot opening. If you need a filler bracket, contact Dell. NOTE: Installing filler brackets over empty card-slot openings is necessary to maintain FCC certification of the computer. The brackets also keep dust and dirt out of your computer. 5. Lower the retention arm and press it into place. AGP and DVI Adapter Cards Removing an AGP or DVI Adapter Card 1. Remove the filler bracket by raising the hinged lever and sliding the bracket up. Press the indented tab on the hinged lever with your thumb until you release the tab. Continue holding the lever and pull the lever up. Filler Bracket Removal

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
1
card cage
2
serial adapter cable
3
serial adapter system board connector (SER2)
Removing a Serial Port Adapter
CAUTION:
Before you perform this procedure, see "
Precautionary Measures
."
1. Remove the card cage (see
step 1
in "Removing a PCI Card").
2. Press the lever on the retention arm and raise the retention arm.
3. Lift and remove the adapter bracket.
4. If you are removing the card permanently, install a filler bracket in the empty card-slot opening.
If you need a filler bracket, contact Dell.
NOTE:
Installing filler brackets over empty card-slot openings is necessary to maintain FCC certification of the
computer. The brackets also keep dust and dirt out of your computer.
5. Lower the retention arm and press it into place.
AGP and DVI Adapter Cards
Removing an AGP or DVI Adapter Card
1. Remove the filler bracket by raising the hinged lever and sliding the bracket up.
Press the indented tab on the hinged lever with your thumb until you release the tab. Continue holding the lever and
pull the lever up.
Filler Bracket Removal