Dell OptiPlex Micro Plus 7010 Owners Manual - Page 72

Installing the antenna module (black cable), Prerequisites, About this task, Steps, Next steps

Get Dell OptiPlex Micro Plus 7010 PDF manuals and user guides View all Dell OptiPlex Micro Plus 7010 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

Installing the antenna module (black cable) Prerequisites If you are replacing a component, remove the existing component before performing the installation process. About this task The following image(s) indicate the location of the antenna module (black cable) and provides a visual representation of the installation procedure. Steps 1. Place the antenna module (black cable) on the chassis. 2. Align the captive screw on the antenna module (black cable) to the screw hole on the chassis. 3. Tighten the captive screw that secures the antenna module (black cable) to the chassis. 4. Route the antenna cable through the routing guides on the chassis. Next steps 1. Install the system board NOTE: The system board can be installed with the memory, coin-cell battery, and processor preattached. 2. Install the optional I/O module (VGA/HDMI/DP/Serial) or the optional Type-C module, whichever applicable. 3. Install the heat sink. 4. Install the fan. 5. Install the speaker. 6. Install the wireless card. 7. Install the M.2 2230 solid-state drive or M.2 2280 solid-state drive, whichever applicable. 8. Install the side cover. 9. Follow the procedure in After working inside your computer. Removing the antenna module (white cable) Prerequisites 1. Follow the procedure in Before working inside your computer. 72 Removing and installing Field Replaceable Units (FRUs)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
Installing the antenna module (black cable)
Prerequisites
If you are replacing a component, remove the existing component before performing the installation process.
About this task
The following image(s) indicate the location of the antenna module (black cable) and provides a visual representation of the
installation procedure.
Steps
1.
Place the antenna module (black cable) on the chassis.
2.
Align the captive screw on the antenna module (black cable) to the screw hole on the chassis.
3.
Tighten the captive screw that secures the antenna module (black cable) to the chassis.
4.
Route the antenna cable through the routing guides on the chassis.
Next steps
1.
Install the
system board
NOTE:
The system board can be installed with the memory, coin-cell battery, and processor preattached.
2.
Install the
optional I/O module (VGA/HDMI/DP/Serial)
or the
optional Type-C module
, whichever applicable.
3.
Install the
heat sink
.
4.
Install the
fan
.
5.
Install the
speaker
.
6.
Install the
wireless card
.
7.
Install the
M.2 2230 solid-state drive
or
M.2 2280 solid-state drive
, whichever applicable.
8.
Install the
side cover
.
9.
Follow the procedure in
After working inside your computer
.
Removing the antenna module (white cable)
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
72
Removing and installing Field Replaceable Units (FRUs)