Dell PowerEdge M420 Dell PowerEdge M620 Systems Owner's Manual - Page 43

Installing The Network Daughter Card/LOM Riser Card

Get Dell PowerEdge M420 PDF manuals and user guides View all Dell PowerEdge M420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

4. Lift the card from the blade system board. 5. Close the blade. 6. Install the blade in the enclosure. Figure 13. Removing or Installing the Network Daughter Card/LOM Riser Card 1. LOM riser card 2. screws (2) 3. LOM riser card connector 4. standoffs (2) 5. tab projections (on the plastic bracket covering the Mezzanine card connectors) Installing The Network Daughter Card/LOM Riser Card CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1. Remove the blade from the enclosure. 2. Open the blade. 3. Install the Network Daughter Card/LOM riser card: a) Align the slots on the card edge with the projection tabs on the plastic bracket covering the mezzanine card slots. b) Lower the card into place until the card connector fits into the corresponding connector on the system board. c) Secure the card with the two screws. 4. Close the blade. 5. Install the blade in the enclosure. 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
4.
Lift the card from the blade system board.
5.
Close the blade.
6.
Install the blade in the enclosure.
Figure 13. Removing or Installing the Network Daughter Card/LOM Riser Card
1. LOM riser card
2. screws (2)
3. LOM riser card connector
4. standoffs (2)
5. tab projections (on the plastic bracket covering the Mezzanine card connectors)
Installing The Network Daughter Card/LOM Riser Card
CAUTION: Many repairs may only be done by a certified service technician. You should only perform
troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or
telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your
warranty. Read and follow the safety instructions that came with the product.
1.
Remove the blade from the enclosure.
2.
Open the blade.
3.
Install the Network Daughter Card/LOM riser card:
a)
Align the slots on the card edge with the projection tabs on the plastic bracket covering the mezzanine card
slots.
b)
Lower the card into place until the card connector fits into the corresponding connector on the system board.
c)
Secure the card with the two screws.
4.
Close the blade.
5.
Install the blade in the enclosure.
43