Dell PowerEdge M420 Dell PowerEdge M520 Systems Owner's Manual - Page 111

interrupt, and send alert., Review platform event configuration.

Get Dell PowerEdge M420 PDF manuals and user guides View all Dell PowerEdge M420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 111 highlights

Error Code Message Information SEL0010 Message Log is almost full. Details When the event log is full, additional events are not written to the log. Older events may be overwritten and lost. Action Backup and clear log at the next maintained time. SEL0012 Message Could not create or initialize the system event log. Details If the system event log fails to initialize, platform status and failure events are not captured. Some management software do not report platform exceptions. Action Reboot the management controller or iDRAC. Cycle system input power. If problem persists call support. SEL1204 Message An unknown system hardware failure detected. LCD Message Unknown system hardware failure. Details If the system event log failed to initialize platform status and failure events are not captured. Some management software will not report platform exceptions. Action Re-configure system to minimum supported configuration. If issues persists, contact support. SEL1209 Message The platform event filter action failed. Details System policies or permissions may prevent the action from executing. If configured, the system does not execute the action on a platform event (such as power down, cycle, interrupt, and send alert). Action Review platform event configuration. SEL1211 Message Details Action The time-stamp clock could not be synchronized. The time stamp on system event log events may not correlate to the system time. Cycle system input power. If problem persists, contact support. SEL1300 Message No bootable media found. Details System setup displays the system boot order. The local video screen may also show additional information. (IPMI sensor type code 1eh - offset 00h). Action Check system boot settings. Check if mass storage controller configuration settings are applicable. SEL1302 Message Non-bootable diskette detected. Details The disk in the drive is not formatted correctly or does not contain the necessary operating system files. Action Replace diskette with a bootable disk. 111

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
Error Code
Message Information
SEL0010
Message
Log is almost full.
Details
When the event log is full, additional events are not written to the log. Older events may be
overwritten and lost.
Action
Backup and clear log at the next maintained time.
SEL0012
Message
Could not create or initialize the system event log.
Details
If the system event log fails to initialize, platform status and failure events are not captured.
Some management software do not report platform exceptions.
Action
Reboot the management controller or iDRAC. Cycle system input power. If problem persists
call support.
SEL1204
Message
An unknown system hardware failure detected.
LCD Message
Unknown system hardware failure.
Details
If the system event log failed to initialize platform status and failure events are not
captured.
Some management software will not report platform exceptions.
Action
Re-configure system to minimum supported configuration. If issues persists, contact
support.
SEL1209
Message
The platform event filter action failed.
Details
System policies or permissions may prevent the action from executing.
If configured, the
system does not execute the action on a platform event (such as power down, cycle,
interrupt, and send alert).
Action
Review platform event configuration.
SEL1211
Message
The time-stamp clock could not be synchronized.
Details
The time stamp on system event log events may not correlate to the system time.
Action
Cycle system input power. If problem persists, contact support.
SEL1300
Message
No bootable media found.
Details
System setup displays the system boot order. The local video screen may also show
additional information. (IPMI sensor type code 1eh - offset 00h).
Action
Check system boot settings. Check if mass storage controller configuration settings are
applicable.
SEL1302
Message
Non-bootable diskette detected.
Details
The disk in the drive is not formatted correctly or does not contain the necessary operating
system files.
Action
Replace diskette with a bootable disk.
111