Home » Dell Manuals » Storage Devices » Dell PowerStore 1200T » Manual Viewer

Dell PowerStore 1200T EMC PowerStore Networking Guide for PowerStore T Models - Page 58

Details, Notes

View all Dell PowerStore 1200T manuals

Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Table 23. Switch resources for Storage services worksheet (completed) Step Details Notes 1. Print this table to record the reserved resources. 2 Reserve and record the IP addresses necessary to configure the ToR switches below: Management IP address for ToR Switch 1 100.0.100.10/24 Management IP address for ToR Switch 2 100.0.100.11/24 Default gateway 100.0.100.1 NTP server 100.0.100.200 3. As a best practice it is recommended to add a spanning tree protocol to the ToR switches. Record the spanning tree protocols to set on each switch. Spanning tree protocol for ToR Switch 1 40960 Spanning tree protocol for ToR Switch 2 45056 4. Choose which layer 2 interconnect you will configure between the switches. ● Highly Recommended: Direct interconnect using Multi-chassis Link Aggregation Group (MC-LAG) ● Direct Interconnect not using MC-LAG ● No direct interconnect between the switches If you will be using MC-LAG, record the ports you will 25 to 25 use to connect the switches together. ToR Switch 1 to ToR Switch 2 port pair 1 ToR Switch 1 to ToR Switch 2 port pair 2 26 to 26 If using MC-LAG, enter the Domain ID. N/A Alternatively, if using uplinks for Layer 2 connectivity between the switches, record the L2 uplink switch ports. VLT domain ID 1 5. If using VLT for the Layer 2 interconnect, record the: VLT MAC address to use for both switch 1 and switch 2. Use the same VLT MAC address for switch 1 and switch 2. 00:00:00:00:00:01 NOTE: You cannot use all zeros (00:00:00:00:00) for the VLT MAC address. VLT priority for ToR Switch 1 VLT priority for ToR Switch 2 MTU setting for Jumbo Frames NOTE: It is recommended to configure jumbo frames with an MTU setting of 9216. The same MTU size must be set on both switches for both node ports. 1 8192 9216 6. Record the ports on the ToR switches that will be used to connect to the uplinks. Uplink A to ToR Switch 1 port 29 Uplink B to ToR Switch 1 port 30 Uplink A to ToR Switch 2 port 29 Uplink B to ToR Switch 2 port 30 58 Configuring PowerStore T model with Dell PowerSwitch Series S4148 Top-of-Rack switches

Section	Page
Dell EMC PowerStore Networking Guide for PowerStore T Models	1
Contents	3
Additional Resources	6
Overview	7
PowerStore T model appliance overview	7
PowerStore T model initial deployment and storage network configuration	7
Supported switches	8
Initial Deployment	10
Initial deployment of PowerStore T model overview	11
Initial deployment of PowerStore T model	11
Prepare to configure the Management switch and networks	12
Reserve network resources for initial deployment	12
Complete the required fields in the Initial Configuration Worksheet	13
Switch and network requirements for initial deployment	16
Management switch connectivity	16
Types of networks required for initial deployment	18
VLAN options during initial deployment	20
IP requirements for initial deployment	21
Configuring Dell PowerSwitch Series for Initial Deployment	23
Configuring with Dell EMC PowerSwitch Series S4148 switches overview	23
Install the Management switch into the PowerStore T model cabinet	23
Get your completed Management Network Preparation Worksheet	24
Steps to configure the Management switch for initial deployment	25
Establish a terminal session to the switch	25
Validate the switch version and licensing	26
Configure the Management switch	27
Cable the Management switch	28
Validate the configuration on the Management switch	30
Network Validation Tool for PowerStore	31
Discovering PowerStore Appliances	32
Discovery with a direct connection	32
Discovery with a remote connection	33
Remote discovery using Discovery Tool	33
Remote discovery with a static IP address	33
Initial configuration of the PowerStore T model appliance	35
Initial Configuration Wizard	35
Get your completed Initial Configuration Worksheet	36
Add Storage Services	39
Storage services overview	40
Storage services	40
Prepare to configure the switches and networks for Storage services	41
Switch resources for Storage services worksheet	41
Network configuration worksheet for Storage services	45
Switch requirements for deployments with storage services	47
Top-of-Rack (ToR) switch connectivity options and requirements	47
Top-of-Rack (ToR) switch to ToR switch (L2) connectivity options	47
Direct interconnect using Multi-chassis Link Aggregation (MC-LAG)	48
Direct interconnect not using MC-LAG	49
No direct interconnect between the switches	50
Network requirements for deployments with storage services	52
Storage services network traffic	52
Link Aggregation Control Protocol requirements	53
VLAN requirements for Storage networks	54
Storage network IP address requirements for adding storage services	54
Configuring PowerStore T model with Dell PowerSwitch Series S4148 Top-of-Rack switches	55
Sample configuration	55
Install the Top-of-Rack switches into the PowerStore T model cabinet	56
Configure Dell PowerSwitch Series for Storage services	57
Get the completed Switch resources for Storage services worksheet	57
Establish a terminal session to the switch	61
Validate the switch version and licensing	62
Configure general settings on the Top-of-Rack (ToR) switches	63
Configure Virtual Link Trunking interconnect	64
Configure the uplink ports on the Top-of-Rack (ToR) switches	66
Configure the iSCSI network on the ToR switches	67
Configure NVMe/TCP network on the ToR switches	68
Configure the Replication and Block Import network on the ToR switches	69
Configure NAS networks on the ToR switches	70
Configure Cluster network on the Top-of-Rack switches	72
Cable Dell PowerSwitch Series ToR switches for Storage services	75
Cable the ToR switches together	75
Cable the Top-of-Rack switches to the core uplinks	76
Cable the base enclosure to the ToR switches	77
Cable the iSCSI and Replication and Import networks	77
Cable the NVMe/TCP network	78
Cable the NAS network	79
Cable the Cluster network	80
Validate PowerSwitch Series configuration with ToR switches	82
Validate configuration on the Top-of-Rack (ToR) switches	82
Network Validation Tool after adding the Top-of-Rack switches to your PowerStore T model deployment	88
Configure Storage networks in PowerStore Manager	89
Create Block-optimized Storage networks in PowerStore Manager	89
Create NAS networks in PowerStore Manager	91
Optionally, add the File Import Interface in PowerStore Manager	92
File Mobility	94
File Mobility overview	94
Create File Mobility in PowerStore Manager	97
Expand a Storage network to run across multiple ports	98
Expand a Storage network	98
Cable the nodes to the ToR switches	98
Configure the VLAN on the ToR switches	99
Add IP addresses and map the Storage network to the ports	100
Create an additional Storage network	101
Create a new Storage network	101
Cable the nodes to the ToR switches	101
Configure a Storage network on the ToR switches	102
Create an additional Storage network in PowerStore Manager	103
Configuring PowerStore T model with ToR switches and no VLT interconnect	104
Steps to configure PowerStore T model with ToR switches without VLT	104
Other Dell EMC PowerSwitch Series configuration operations	105
Dell EMC SmartFabric Services	105
Dell EMC SmartFabric Storage Software	105
Reset the switch to factory settings	105
Running configuration of PowerSwitch Series used in PowerStore T model deployments	106
Example of running configuration for the Management switch	106

Match case Limit results 1 per page

Table 23. Switch resources for Storage services worksheet (completed)

Step

Details

Notes

Print this table to record the reserved resources.

Reserve and record the IP addresses necessary to configure the ToR switches below:

Management IP address for ToR Switch 1

100.0.100.10/24

Management IP address for ToR Switch 2

100.0.100.11/24

Default gateway

100.0.100.1

NTP server

100.0.100.200

As a best practice it is recommended to add a spanning tree protocol to the ToR switches.

Record the spanning tree protocols to set on each switch.

Spanning tree protocol for ToR Switch 1

40960

Spanning tree protocol for ToR Switch 2

45056

Choose which layer 2 interconnect you will configure between the switches.

●

Highly Recommended

: Direct interconnect using Multi-chassis Link Aggregation Group (MC-LAG)

●

Direct Interconnect not using MC-LAG

●

No direct interconnect between the switches

If you will be using MC-LAG, record the ports you will

use to connect the switches together.

ToR Switch 1 to ToR Switch 2 port pair 1

25 to 25

ToR Switch 1 to ToR Switch 2 port pair 2

26 to 26

If using MC-LAG, enter the Domain ID.

N/A

Alternatively, if using uplinks for Layer 2 connectivity

between the switches, record the L2 uplink switch

ports.

VLT domain ID 1

If using VLT for the Layer 2 interconnect, record the:

VLT MAC address to use for both switch 1 and switch

Use the same VLT MAC address for switch 1 and

switch 2.

NOTE:

You cannot use all zeros

(

00:00:00:00:00

) for the VLT MAC address.

00:00:00:00:00:01

VLT priority for ToR Switch 1

VLT priority for ToR Switch 2

8192

MTU setting for Jumbo Frames

NOTE:

It is recommended to configure jumbo

frames with an MTU setting of 9216. The same

MTU size must be set on both switches for both

node ports.

9216

Record the ports on the ToR switches that will be used to connect to the uplinks.

Uplink A to ToR Switch 1

port 29

Uplink B to ToR Switch 1

port 30

Uplink A to ToR Switch 2

port 29

Uplink B to ToR Switch 2

port 30

Configuring PowerStore T model with Dell PowerSwitch Series S4148 Top-of-Rack switches