Dell PowerStore 1200T EMC PowerStore Networking Guide for PowerStore T Models - Page 61

Establish a terminal session to the switch

Get Dell PowerStore 1200T PDF manuals and user guides View all Dell PowerStore 1200T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Table 23. Switch resources for Storage services worksheet (completed) (continued) Step Details Notes switches for both node ports. Cluster When cabling the nodes for the cluster network: ● Ports 0 and 1 of the 4-port card are reserved for clustering ● Ports 0 and 1 on the 4-port card on the same node must connect to opposite switches ● Port 0 on the 4-port card on Node A and Port 0 on the 4-port card on Node B must connect to opposite switches ● Port 1 on the 4-port card on Node A and Port 1 on the 4-port card on Node B must connect to opposite switches VLAN ID 1 Record the LACP (port channel) ID for the node connections: Node A port channel 30 Node B port channel 40 Record which appliance node To cable to the ToR switch port number and port: Node A ToR Switch 1 Port 0 of the 4-port card Switch port 1 Node A Port 1 of the 4-port card ToR Switch 2 Switch port 1 Node B Port 0 of the 4-port card ToR Switch 1 Switch port 54 Node B Port 1 of the 4-port card ToR Switch 2 Switch port 54 MTU setting for Jumbo Frames NOTE: It is recommended to configure jumbo frames with an MTU setting of 9216. The same MTU size must be set on both switches for both node ports. 9216 Establish a terminal session to the switch Perform the following steps to establish a terminal session to the serial console port on the Dell EMC PowerSwitch Series S4148 switch. These steps are specific to establishing connections to Dell EMC PowerSwitch S4148-ON switches. For console serial port cable requirements, and further details refer to the Dell EMC PowerSwitch S4100-ON Series Installation Guide located at: https://www.dell.com/support/home/us/en/04/product-support/product/networking-s4148f-on/docs. You must establish a terminal session to each of the switches to configure the switches for deployment. 1. Power on the switch. 2. Use a serial cable to connect a computer to the serial console port, which is the top port located on the PSU-side of the PowerSwitch. Configuring PowerStore T model with Dell PowerSwitch Series S4148 Top-of-Rack switches 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Table 23. Switch resources for Storage services worksheet (completed) (continued)
Step
Details
Notes
switches for both node
ports.
Cluster
When cabling the nodes for the cluster network:
●
Ports 0 and 1 of the 4-port card are reserved for
clustering
●
Ports 0 and 1 on the 4-port card on the same node
must connect to opposite switches
●
Port 0 on the 4-port card on Node A and Port 0
on the 4-port card on Node B must connect to
opposite switches
●
Port 1 on the 4-port card on Node A and Port 1
on the 4-port card on Node B must connect to
opposite switches
VLAN ID
1
Record the LACP (port channel) ID for the node connections:
Node A
port channel 30
Node B
port channel 40
Record which appliance node
port
To cable to the ToR switch
number and port:
Node A
Port 0 of the 4-port card
ToR Switch
1
Switch port
1
Node A
Port 1 of the 4-port card
ToR Switch
2
Switch port
1
Node B
Port 0 of the 4-port card
ToR Switch
1
Switch port
54
Node B
Port 1 of the 4-port card
ToR Switch
2
Switch port
54
MTU setting for Jumbo
Frames
NOTE:
It is recommended
to configure jumbo frames
with an MTU setting of
9216. The same MTU size
must be set on both
switches for both node
ports.
9216
Establish a terminal session to the switch
Perform the following steps to establish a terminal session to the serial console port on the Dell EMC PowerSwitch Series S4148
switch.
These steps are specific to establishing connections to Dell EMC PowerSwitch S4148-ON switches.
For console serial port cable requirements, and further details refer to the
Dell EMC PowerSwitch S4100-ON Series Installation
Guide
located at:
.
You must establish a terminal session to each of the switches to configure the switches for deployment.
1.
Power on the switch.
2.
Use a serial cable to connect a computer to the serial console port, which is the top port located on the PSU-side of the
PowerSwitch.
Configuring PowerStore T model with Dell PowerSwitch Series S4148 Top-of-Rack switches
61