Dell PowerVault MD3000i Hardware Owner's Manual - Page 16

green and a bicolor green/amber status LED see The activity, patterns for the status LED. - configuration

Get Dell PowerVault MD3000i PDF manuals and user guides View all Dell PowerVault MD3000i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Table 1-2. Front-Panel Components (continued) Component Icon Condition Power LED (green) When lit, at least one power supply is supplying power to the enclosure. Split mode LED (green) Enclosure mode switch Because this mode is unused in the system, this LED should always be unlit. NOTE: This LED comes on if the enclosure mode switch on the enclosure's front panel is in the split mode position before the enclosure is turned on. The function of this switch is not applicable to your MD3000i. However, if additional MD1000 expansion enclosures are daisy chained to your system, the enclosure mode switch on those enclosures must be in unified-mode position. NOTE: This switch must be set prior to turning on the system. Changing the switch setting after the system is turned on will have no effect on enclosure configuration until the system goes through a complete power cycle. Physical Disk Carrier LED Indicators Each physical disk carrier in your enclosure has two LEDs: an activity LED (green) and a bicolor (green/amber) status LED (see Figure 1-3). The activity LED flashes whenever the physical disk is accessed. Table 1-3 lists the flash patterns for the status LED. 16 About Your System

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
16
About Your System
Physical Disk Carrier LED Indicators
Each physical disk carrier in your enclosure has two LEDs: an activity LED
(green) and a bicolor (green/amber) status LED (see Figure 1-3). The activity
LED flashes whenever the physical disk is accessed. Table 1-3 lists the flash
patterns for the status LED.
Power LED (green)
When lit, at least one power supply is
supplying power to the enclosure.
Split mode LED (green)
Because this mode is unused in the system, this
LED should always be unlit.
NOTE:
This LED comes on if the enclosure mode
switch on the enclosure’s front panel is in the
split mode position before the enclosure is
turned on.
Enclosure mode switch
The function of this switch is not applicable to
your MD3000i. However, if additional MD1000
expansion enclosures are daisy chained to your
system, the enclosure mode switch on those
enclosures must be in unified-mode position.
NOTE:
This switch must be set prior to turning
on the system. Changing the switch setting after
the system is turned on will have no effect on
enclosure configuration until the system goes
through a complete power cycle.
Table 1-2.
Front-Panel Components
(continued)
Component
Icon
Condition