Dell S5224F-ON EMC PowerSwitch S5200F-ON Series Installation Guide February 20 - Page 29

One-half U front-rack installation, Rack mount safety considerations

Get Dell S5224F-ON PDF manuals and user guides View all Dell S5224F-ON manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

NOTE: The illustrations in this document are not intended to represent a specific switch. NOTE: Do not the use the mounted ReadyRails as a shelf or a workplace. Rack mount safety considerations ● Rack loading-Overloading or uneven loading of racks may result in shelf or rack failure, possibly damaging the equipment and causing personal injury. Stabilize racks in a permanent location before loading begins. Mount the components starting at the bottom of the rack, then work to the top. Do not exceed your rack's load rating. ● Power considerations-Connect only to the power source specified on the unit. When you install multiple electrical components in a rack, ensure that the total component power ratings do not exceed the circuit capabilities. Overloaded power sources and extension cords present fire and shock hazards. ● Elevated ambient temperature-If installed in a closed rack assembly, the operating temperature of the rack environment may be greater than the room ambient temperature. Use care not to exceed the 45°C (113°F) maximum ambient temperature of the switch. ● Reduced air flow-Install the equipment in the rack so that the amount of airflow required for safe operation of the equipment is not compromised. ● Reliable earthing-Maintain reliable earthing of rack-mounted equipment. Pay particular attention to the supply connections other than the direct connections to the branch circuit, for example, use of power strips. ● Do not mount the equipment with the back panel facing downward. One-half U front-rack installation Install the S5212F-ON switch using the following installation instructions. NOTE: To install the S5232F-ON, S5248F-ON, and S5224F-ON switches, see One U ReadyRails installation. To install the S5296F-ON switch, see Two U four-post rack assembly. The dual-tray mounting rails ship with the dual tray, not with the switch. You must supply eight rackmount screws for this installation. To install the one-half U switch: ● Attach the rails to the dual tray. ● Install the dual tray in the four-post rack. ● (Recommended) Attach the ground cable to the switch. ● Install the switch in the dual tray. NOTE: Do not install the dual tray in a two-post rack. 1. Remove the dual tray and the rails from the shipping packaging and place them on a clean antistatic surface. 2. Line up the three holes on the inner switch rail with the dual-tray mounting heads. 3. Attach the rail to the dual tray. Slide the rail back until it locks into place. 4. Repeat with the other side. S5200F-ON Series switch installation 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
NOTE:
The illustrations in this document are not intended to represent a specific switch.
NOTE:
Do not the use the mounted ReadyRails as a shelf or a workplace.
Rack mount safety considerations
●
Rack loading—Overloading or uneven loading of racks may result in shelf or rack failure, possibly damaging the equipment
and causing personal injury. Stabilize racks in a permanent location before loading begins. Mount the components starting at
the bottom of the rack, then work to the top. Do not exceed your rack’s load rating.
●
Power considerations—Connect only to the power source specified on the unit. When you install multiple electrical
components in a rack, ensure that the total component power ratings do not exceed the circuit capabilities. Overloaded
power sources and extension cords present fire and shock hazards.
●
Elevated ambient temperature—If installed in a closed rack assembly, the operating temperature of the rack environment
may be greater than the room ambient temperature. Use care not to exceed the 45°C (113°F) maximum ambient
temperature of the switch.
●
Reduced air flow—Install the equipment in the rack so that the amount of airflow required for safe operation of the
equipment is not compromised.
●
Reliable earthing—Maintain reliable earthing of rack-mounted equipment. Pay particular attention to the supply connections
other than the direct connections to the branch circuit, for example, use of power strips.
●
Do not mount the equipment with the back panel facing downward.
One-half U front-rack installation
Install the S5212F-ON switch using the following installation instructions.
NOTE:
To install the S5232F-ON, S5248F-ON, and S5224F-ON switches, see
One U ReadyRails installation
. To install the
S5296F-ON switch, see
Two U four-post rack assembly
.
The dual-tray mounting rails ship with the dual tray, not with the switch. You must supply eight rackmount screws for this
installation.
To install the one-half U switch:
●
Attach the rails to the dual tray.
●
Install the dual tray in the four-post rack.
●
(Recommended) Attach the ground cable to the switch.
●
Install the switch in the dual tray.
NOTE:
Do not install the dual tray in a two-post rack.
1.
Remove the dual tray and the rails from the shipping packaging and place them on a clean antistatic surface.
2.
Line up the three holes on the inner switch rail with the dual-tray mounting heads.
3.
Attach the rail to the dual tray. Slide the rail back until it locks into place.
4.
Repeat with the other side.
S5200F-ON Series switch installation
29