Dell S5296F-ON EMC PowerSwitch S5200F-ON Series Setup Guide - Page 22

Optics installation, Optics removal, Switch start up, After switch installation, Power up sequence

Get Dell S5296F-ON PDF manuals and user guides View all Dell S5296F-ON manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Optics installation WARNING: When working with optical fibers, follow all warning labels and always wear eye protection. Never look directly into the end of a terminated or unterminated fiber or connector as it may cause eye damage. 1. Position the optic so it is in the correct position. The optic has a key that prevents it from being inserted incorrectly. 2. Insert the optic into the port until it gently snaps into place. NOTE: When you cable the ports, be sure not to interfere with the airflow from the small vent holes above and below the ports. Optics removal Remove an optic by pushing the tab on the optic and sliding the optic from the port. When removing optics with direct attach cables (DACs) from the port, pull the release tab firmly and steadily. Before pulling the release tab, you may need to gently push the optic into the port to ensure that it is seated properly. Do not jerk or tug repeatedly on the tab. Switch start up Supply power to the S5200F-ON Series switch after you mount it in a rack or cabinet. Reinspect your switch before you turn it on. Verify the following: • Optional: The equipment is properly secured to the rack and properly grounding the switch. • Optional: The equipment rack is properly mounted and grounded. • The ambient temperature around the unit, which may be higher than the room temperature, is within the limits that are specified for the S5200F-ON Series switch. • There is sufficient airflow around the unit. • The input circuits are correctly sized for the loads and that you use sufficient overcurrent protection devices. CAUTION: Do not start up the switch if you did not install a fan module. NOTE: A US AC or DC power cable is included for powering up an AC or DC power supply. You must order all other power cables separately. NOTE: ESD damage can occur if components are mishandled. Always wear an ESD-preventive wrist or heel ground strap when handling the switch and its components. Power up sequence When the switch powers up, the fans immediately come on at high speed. The fan speed slows as the switch continues to boot. After switch installation After you have securely installed and powered on the S5200F-ON Series switch: • If you are using Dell EMC software, see switch documentation at www.dell.com/support. • If you are using third-party software, see ONIE documentation at www.onie.org. 22 S5200F-ON Series switch Installation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
Optics installation
WARNING:
When working with optical fibers, follow all warning labels and always wear eye protection. Never look
directly into the end of a terminated or unterminated fiber or connector as it may cause eye damage.
1.
Position the optic so it is in the correct position.
The optic has a key that prevents it from being inserted incorrectly.
2.
Insert the optic into the port until it gently snaps into place.
NOTE:
When you cable the ports, be sure not to interfere with the airflow from the small vent holes above and below
the ports.
Optics removal
Remove an optic by pushing the tab on the optic and sliding the optic from the port.
When removing optics with direct attach cables (DACs) from the port, pull the release tab firmly and steadily. Before pulling the release
tab, you may need to gently push the optic into the port to ensure that it is seated properly. Do not jerk or tug repeatedly on the tab.
Switch start up
Supply power to the S5200F-ON Series switch after you mount it in a rack or cabinet.
Reinspect your switch before you turn it on. Verify the following:
•
Optional: The equipment is properly secured to the rack and properly grounding the switch.
•
Optional: The equipment rack is properly mounted and grounded.
•
The ambient temperature around the unit, which may be higher than the room temperature, is within the limits that are specified for
the S5200F-ON Series switch.
•
There is sufficient airflow around the unit.
•
The input circuits are correctly sized for the loads and that you use sufficient overcurrent protection devices.
CAUTION:
Do not start up the switch if you did not install a fan module.
NOTE:
A US AC or DC power cable is included for powering up an AC or DC power supply. You must order all other
power cables separately.
NOTE:
ESD damage can occur if components are mishandled. Always wear an ESD-preventive wrist or heel ground strap
when handling the switch and its components.
Power up sequence
When the switch powers up, the fans immediately come on at high speed. The fan speed slows as the switch continues to boot.
After switch installation
After you have securely installed and powered on the S5200F-ON Series switch:
•
If you are using Dell EMC software, see switch documentation at
www.dell.com/support
.
•
If you are using third-party software, see ONIE documentation at
www.onie.org
.
22
S5200F-ON Series switch Installation