Denon ADV-1000 Owners Manual - Page 36

Input mode when playing DTS sources, Input signal display

Get Denon ADV-1000 PDF manuals and user guides View all Denon ADV-1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

ENGLISH 4 Start playback on the selected component. • For operating instructions, refer to the component's manual. 5 Either turn the MASTER VOLUME dial on the main unit or use the VOLUME buttons on the remote control unit to adjust the volume. M.VOLUME -20 The volume level is displayed on the display. MASTER VOLUME VOLUME Input mode display • In the AUTO mode • In the DIGITAL PCM mode Lit DIG AUTO PCM DTS ANA One of these lights, depending on the input signal. DIG AUTO PCM DTS ANA • In the DIGITAL DTS mode DIG AUTO PCM DTS ANA • In the ANALOG mode DIG AUTO PCM DTS ANA Main unit Remote control unit • The volume can be adjusted within the range -60 to 0 to +18 dB. Note that depending on the input signal, surround mode, speaker settings and channel level setting, it may not be possible to adjust the volume up to +18 dB. Input mode when playing DTS sources • If DTS-compatible CDs are played in the "PCM" mode, noise is output because DTS playback is not possible. To play a DTS-compatible source, be sure to set the input mode to "AUTO" or "DTS". • Noise may be generated at the beginning of playback and while searching during DTS playback in the AUTO mode. If so, play in the DTS mode. 2 To check the currently playing program source, etc. Press the STATUS button. STATUS FUNCTION / SELECT STATUS Input signal display • DOLBY DIGITAL • DTS • PCM DIG PCM DTS DIGITAL PRO LOGIC II One of these DIG PCM DTS lights, depending DIGITAL on the input signal. DIG PCM DTS DIGITAL • "DIG" lights when digital signals are input properly. If "DIG" is flashing, check whether the connections are proper and whether the input component's power is on. Input mode when playing CD sources • When playing CDs containing recordings of live concerts, etc., in the "AUTO" mode, the sound may be slightly broken at the beginning. If this happens, switch to the "PCM" mode. Main unit Main unit Remote control unit To perform this operation on the main unit, press the STATUS button, then turn the FUNCTION/SELECT knob. The current program source and surround settings are shown on the display each time the button is pressed. (When the function is set to DVD, the information is also displayed on the TV screen.) 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
36
4
Start playback on the selected component.
• For operating instructions, refer to the component’s
manual.
• The volume can be adjusted within the range -60 to 0 to
+18 dB. Note that depending on the input signal, surround
mode, speaker settings and channel level setting, it may
not be possible to adjust the volume up to +18 dB.
5
Either turn the MASTER VOLUME dial on the main unit or
use the VOLUME buttons on the remote control unit to
adjust the volume.
M.VOLUME -20
MASTER VOLUME
Main unit
VOLUME
Remote control unit
The volume level is displayed
on the display.
Input mode when playing DTS sources
•
If DTS-compatible CDs are played in the “PCM” mode, noise is
output because DTS playback is not possible.
To play a DTS-compatible source, be sure to set the input mode
to “AUTO” or “DTS”.
•
Noise may be generated at the beginning of playback and while
searching during DTS playback in the AUTO mode. If so, play in
the DTS mode.
• “DIG” lights when digital signals are input properly. If “DIG” is
flashing, check whether the connections are proper and whether
the input component’s power is on.
PRO LOGIC II
DIG
PCM
DIGITAL
DTS
DIG
PCM
DIGITAL
DTS
DIG
PCM
DIGITAL
DTS
AUTO
ANA
DIG
PCM
DTS
ANA
DIG
PCM
AUTO
DTS
ANA
DIG
PCM
AUTO
DTS
ANA
DIG
PCM
AUTO
DTS
Input mode display
•
In the AUTO mode
•
In the DIGITAL PCM mode
•
In the DIGITAL DTS mode
•
In the ANALOG mode
One of these lights, depending on
the input signal.
Lit
Input signal display
•
DOLBY DIGITAL
• DTS
• PCM
STATUS
Main unit
FUNCTION
/ SELECT
Main unit
STATUS
Remote control unit
2
To check the currently playing program source, etc.
Press the STATUS button.
ENGLISH
To perform this operation on the main unit, press the
STATUS button, then turn the FUNCTION/SELECT knob.
The current program source and surround settings are shown
on the display each time the button is pressed. (When the
function is set to DVD, the information is also displayed on the
TV screen.)
Input mode when playing CD sources
•
When playing CDs containing recordings of live concerts, etc., in
the “AUTO” mode, the sound may be slightly broken at the
beginning. If this happens, switch to the “PCM” mode.
One of these
lights, depending
on the input
signal.