Denon D-F101S Owners Manual - Page 16

ENGLISH Press the MEMORY/SET button. • "PM 2" is stored in the memory for the hours position. 10 MEMORY / SET TUNING Use the TUNING buttons to DOWN UP set the minutes position to "35". 11 Press the MEMORY/SET button. • The on time is stored in the memory and the timer off time setting mode is set. 12 "E" and "oFF" appear alternately in the display in the steps 12 to 15. MEMORY / SET TUNING DOWN UP Use the TUNING buttons to set the hours position to 13 "PM 2". Press the MEMORY/SET button. • "PM 2" is stored in the memory for the hours position. 14 MEMORY / SET TUNING Use the TUNING buttons to DOWN UP set the minutes position to "56". 15 Press the MEMORY/SET button. 16 • The off time is stored in the memory. MEMORY / SET TUNING Use the TUNING button to DOWN UP select "E oN". • The " " mark lights. 17 Turn off the power. When the DRA-F101 is connected in a system with the D-F101 series, press the 18 power button on the receiver. • The standby mode is set. (The power switch indicator turn orange and display turn off.) SYSTEM ON / STANDBY ✽ Turning on and off the timer standby ON/OFF • In TIMER STANDBY mode, each time the TUNING button is pressed, the setting changes as follows: 1 1 oN/E oN: Both once and everyday timers 1 are activated. (The mark 1 lights.) 1_ _/E oN: Only the everyday timer is 1 activated. (The mark lights.) 1 1 oN/E_ _: Only the once timer is activated. 1 (The mark lights.) 1 1 1_ _/E_ _: Both timers are canceled. (The mark turns off.) • When you set only the everyday timer, the indication changes between 1_ _/E_ _ and 1_ _/E oN. • When you set only the once timer, the indication changes between 1_ _/E_ _ and 1 oN/E_ _. • When you complete the setting, the display automatically returns to the former state after 5 seconds. • To change the settings of TIMER STANDBY, press TIMER button to set the unit in TIMER STANDBY mode first, the use TUNING button to make changes. ✽ When the timer start time is reached, the timer operates. ✽ If "ONCE" is selected in step 3, the once timer setting mode is selected. Set the timer using the same procedure. At steps 4 and 8 through 15, "1" (for once) is displayed instead of "E". The once timer is activated when "1 oN" is displayed at step 17. NOTES: • The timer standby indicator (" ") will not light if the current time is not set. If this happens, set the current time. (Refer to "Setting the Current Time" on page 15.) • When the timer on time is reached while in the standby mode, operation switches to the operation set with the timer. (The timer setting has priority.) • Set the standby mode when using the timer. The timer may not operate properly if the power is on. (4) Using the timer The time and timer functions are incorporated in this unit. Timer Settings 2 Types of timer operations EVERYDAY TIMER : Use this to turn the power on and standby at the same times every day. ONCE TIMER : Use this to turn the power on and standby once. SLEEP TIMER : Use this to set the power to turn standby after 10 to 60 minutes, in steps of 10 minutes (operated from the remote control unit). 2 Notes on timer settings • Be sure to set the current time beforehand. • To listen to a radio program using the timer, be sure to preset the station beforehand. (Refer to "Presetting AM and FM Stations" on Page 14.) Power Failures If the power cord is unplugged or there is a power failure, the settings of the current time and once timer are erased and the time display will flash. If this happens, reset the current time and the once timer. Also check the timer and tuner presettings, and reset them if they have been cleared. Checking the Settings To check the timer settings, press the TIMER button for at least 3 seconds to select EVERYDAY or ONCE TIMER. Next, press the TUNING button to select EVERYDAY or ONCE TIMER, then press MEMORY/SET button repeatedly to display in order: Timer Start mode, and (when in TUNER mode) the reception band and preset channel number, Timer On time, Timer Off time, Press the MEMORY/SET button again to return to the current mode display. Changing the Settings Repeat the timer setting operation to erase the previous settings and set the new settings. Note on Setting the Timer If the time set with the timer is reached while the system power is on, the operation switches to the operation set by the timer. 16