Dewalt DCW600B Instruction Manual - Page 6
Additional Safety Information, BATTERIES AND CHARGERS, Important Safety Instructions for All, - router
View all Dewalt DCW600B manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 6 highlights
English possible injury. When climb-cutting is required (backing around a corner), exercise extreme caution to maintain control of router. Make smaller cuts and remove minimal material with each pass. • Do not hand-hold the router in an upside-down or horizontal position. The motor can separate from the base if not properly attached according to the instructions. • Before starting the motor clear the work area of all foreign objects. • Do not use in a router table. • Always keep the chip shield (if included) clean and in place. • Do not press spindle lock button while the motor is running. Doing so can damage the spindle lock. • Always make sure the work surface is free from nails and other foreign objects. Cutting into a nail can cause the bit and the tool to jump. Additional Safety Information WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT: • ANSI Z87.1 eye protection (CAN/CSA Z94.3), • ANSI S12.6 (S3.19) hearing protection, • NIOSH/OSHA/MSHA respiratory protection. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemicallytreated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. • Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals. WARNING: Use of this tool can generate and/ or disperse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body. WARNING: Always wear proper personal hearing protection that conforms to ANSI S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss. CAUTION: When not in use, place tool on its side on a stable surface where it will not cause a tripping or falling hazard. Some tools with large battery packs will stand upright on the battery pack but may be easily knocked over. • Air vents often cover moving parts and should be avoided. Loose clothes, jewelry or long hair can be caught in moving parts. The label on your tool may include the following symbols. The symbols and their definitions are as follows: V volts or AC/DC..... alternating or Hz hertz direct current min minutes Class II or DC....... direct current Construction Class I Construction (double insulated) (grounded) no no load speed .../min per minute n rated speed BPM beats per minute earthing terminal IPM impacts per minute safety alert symbol RPM revolutions per visible radiation minute wear respiratory sfpm surface feet per protection minute wear eye SPM strokes per minute protection A amperes W watts or AC alternating current wear hearing protection read all documentation BATTERIES AND CHARGERS The battery pack is not fully charged out of the carton. Before using the battery pack and charger, read the safety instructions below and then follow charging procedures outlined. When ordering replacement battery packs, be sure to include the catalog number and voltage. Your tool uses a DeWALT charger. Be sure to read all safety instructions before using your charger. READ ALL INSTRUCTIONS Important Safety Instructions for All Battery Packs WARNING: Read all safety warnings and all instructions for the battery pack, charger and power tool. Failure to follow the warnings and instructions may result in electric shock, fire and/ or serious injury. • Do not charge or use the battery pack in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Inserting or removing the battery pack from the charger may ignite the dust or fumes. • NEVER force the battery pack into the charger. DO NOT modify the battery pack in any way to fit into a non-compatible charger as battery pack may rupture causing serious personal injury. Consult 4