Epson ActionNote 660C User Manual - Page 42

Using Password Security, Ctrl Alt S, Caution

Get Epson ActionNote 660C PDF manuals and user guides View all Epson ActionNote 660C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Your computer is setup to start at high speed. If you want to change the speed (through MS-DOS only), use the following key sequences: Command Ctrl Alt Ctrl Alt Function Sets CPU speed to low (12 MHz) Sets CPU speed to high Using Password Security Your ActionNote offers two types of passwords: a Boot password and an SCU password. If you set a Boot password, you must enter the password every time you turn on or reset your computer. If you set an SCU password, the computer prompts you to enter the password only when you press Ctrl Alt S to run the System Configuration utility. If you want to enter, change, or delete a password, run the System Configuration utility as described in Chapter 1. When you see a prompt to enter a password, see the next sections. Caution Once you set a Boot password, you cannot access your system unless you enter it correctly, so make a note of it. If you forget your password, call the EPSON Connection. 2-10 Using Your Computer

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
Your computer is setup to start at high speed. If you want to
change the speed (through MS-DOS only), use the following
key sequences:
Command
Function
Ctrl Alt
Sets CPU speed to low (12 MHz)
Ctrl Alt
Sets CPU speed to high
Using Password Security
Your ActionNote offers two types of passwords: a Boot
password and an SCU password. If you set a Boot password,
you must enter the password every time you turn on or reset
your computer. If you set an SCU password, the computer
prompts you to enter the password only when you press
Ctrl Alt S
to run the System Configuration utility.
If you want to enter, change, or delete a password, run the
System Configuration utility as described in Chapter 1. When
you see a prompt to enter a password, see the next sections.
Caution
Once you set a Boot password, you cannot access your
system unless you enter it correctly, so make a note of it. If
you forget your password, call the EPSON Connection.
2-10
Using Your Computer