Epson Ensemble HD 8100 Installation Guide - Page 51

Adjusting the Image, Insert Batteries, Turn On the System

Get Epson Ensemble HD 8100 - Home Cinema System PDF manuals and user guides View all Epson Ensemble HD 8100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Adjusting the Image Follow the steps in this section to adjust your system and make it ready for use. Insert Batteries Insert the included batteries into the remote controls for both the projector and the Ensemble HD system, as shown below. Note The projector remote control is used only to make initial adjustments to the projector, but it should be saved in case it's needed after installation. Projector remote control Insert 2 AA batteries: Ensemble HD remote control Insert 4 AAA batteries: Turn On the System 1 Remove the protective foam from the projector lens, if you haven't done so already. 2 Remove the projector lens cap. 3 Make sure the MAIN menu is displayed on the Ensemble HD remote control. If necessary, press the MAIN button. MAIN button MAIN DVD CABLE SAT HD RADIO 1 OF 2 ON button 4 Point the remote control at the screen and press the ON button to turn on the system. The screen comes down and the projector and AV controller turn on. Note Make sure the remote control remains pointed at the screen until the built-in macro finishes turning on all the equipment. (You see the icon flash on the remote control screen.) The projector lamp takes up to 30 seconds to achieve full brightness. 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
51
Adjusting the Image
Follow the steps in this section to adjust your system and make it ready for use.
Insert Batteries
Insert the included batteries into the remote controls for both the projector and the Ensemble HD system, as
shown below.
Note
The projector remote control is used only to make initial adjustments to the projector, but it should be saved in case it’s
needed after installation.
Turn On the System
1
Remove the protective foam from the projector lens, if you haven’t done so already.
2
Remove the projector lens cap.
3
Make sure the MAIN menu is displayed on the Ensemble HD remote control. If necessary, press the
MAIN
button.
4
Point the remote control at the screen and press the
ON
button to turn on the system. The screen comes
down and the projector and AV controller turn on.
Note
Make sure the remote control remains pointed at the screen until the built-in macro finishes turning on all the
equipment. (You see the
icon flash on the remote control screen.)
The projector lamp takes up to 30 seconds to achieve full brightness.
Projector remote control
Insert 2 AA batteries:
Ensemble HD remote control
Insert 4 AAA batteries:
MAIN
DVD
CABLE
SAT
HD
RADIO
1 OF 2
ON
button
MAIN
button