Home » Epson Manuals » Laptops » Epson Equity LT-386SX » Manual Viewer

Epson Equity LT-386SX User Manual - Page 2

device, pursuant to Subpart B of Part 15 of FCC Rules. Only - computer

Get Epson Equity LT-386SX PDF manuals and user guides

View all Epson Equity LT-386SX manuals

Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

This equipment generates and uses radio frequency energy and if it is not installed and used properly, that is, in strict accordance with the manufacturer's instructions, it may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio and television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures: . Reorient the receiving antenna l Relocate the computer with respect to the receiver l Move the computer away from the receiver l Plug the computer into a different outlet so that the computer and receiver are on different branch circuits. If necessary, consult your dealer or an experienced radio/television technician for additional suggestions. You may find the following booklet prepared by the Federal Communications Commission helpful: "Television Interference Handbook" This booklet is available from the U.S. Government Printing Office, Washington DC 20402. Stock No. 004-000-00450-7 Note: If the interference stops, it was probably caused by the computer or its peripheral devices. To further isolate the problem: Disconnect the peripheral devices and their input/output cables one at a time. If the interference stops, it is caused by either the peripheral device or its I/O cable. These devices usually require shielded I/O cables. For Epson peripheral devices, you can obtain the proper shielded cable from your dealer. For non-Epson peripheral devices, contact the manufacturer or dealer for assistance. WARNING: This equipment has been certified to comply with the limits for a Class B computer device, pursuant to Subpart B of Part 15 of FCC Rules. Only peripherals (computer input/output devices, terminals, printers, etc.) certified to comply with the Class B limits may be attached to this computer. Operation with noncertified peripherals is likely to result in interference to radio and TV reception. The connection of a nonshielded equipment interface cable to this equipment will invalidate the FCC Certification of this device and may cause interference levels that exceed the limits established by the FCC for this equipment. DOC COMPLIANCE STATEMENT FOR CANADIAN USERS This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of the Canadian Department of Communications. Conformation 6 Les Normes d'Emission Radioelectriques Canadiennes Le present appareil numerique n'emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques de Classe B prescrites dans le reglement sur le brouillage radioelectriques edict6 par le Minis&e des Communications du Canada.

Section	Page
Front Matter	1
Contents	7
Introduction	14
How To Use This Manual	18
Where To Get Help	19
Chapter 1	20
Chap 1-Setting Up Your System	20
Unpacking	21
Installing the Hard Disk Drive	23
Connecting a Printer	26
Using the Parallel Interface	27
Using the Serial Interface	29
Connecting the AC Adapter	30
Connecting the Power Cord	33
Starting the System	34
Turning On the Computer	34
Adjusting Screen Contrast and Brightness	36
Initial Screen Display	37
Running the SETUP Program	37
Starting the SETUP Program	38
Setting the Date	39
Setting the Diskette Drive(s)	40
Setting the Hard Disk Drive	40
Setting the Primary Display	41
Setting the Keyboard	41
Setting the Scratch RAM Option	42
Setting the CPU Clock Setting	42
Setting the Shadow RAM	42
Setting the Standby Mode	43
Setting the LCD Contrast	43
Saving Your Settings	44
Inserting the Install Diskette	45
Chap 2-Use the Equity LT-386SX	47
Using the AC Adapter	47
Using the Battery	48
Connecting the Battery Pack	50
Status Indicator Bar	53
Opening and Closing the Screen	55
Using the Handle	56
Selecting Execution Speed	57
Selecting LCD Screen Contrast	57
Changing the Gray Scale Pattern for Any Color	58
Special Keys on the Equity LT-386SX Keyboard	62
Using Diskettes	64
How Diskettes Work	65
Choosing Diskettes for the Equity LT-386SX	65
Caring for Diskettes	66
Inserting and Removing Diskettes	68
Making Backup Copies	69
Write-Protecting Diskettes	69
Using the Hard Disk Drive	70
Caring for the Hard Disk	70
Protecting the Data on Your Hard Disk	71
Improving Hard Disk Performance	71
Turning Off the Hard Disk	72
Modifying the AUTOEXEC.BAT File	72
Resetting the Computer	74
Turning Off the Computer	75
Chap 3-Using MS-DOS With Your Computer	76
Starting and Exiting MS-MDOS	77
Changing the Current Drive	77
The MS-DOS Command Format	79
Entering MS-DOS Commands	80
Storing Data	80
Using Directories	81
The Current Directory	83
Listing the Contents of a Directory	84
Using Pathnames	85
Creating Directories	86
Changing Directories	87
Copying From One Directory to Another	88
Deleting a Directory	89
Formatting Diskettes	89
Formatting a 1.44MB Diskette	90
Formatting a 720KB Diskette	91
Copying Data	92
Using DISKCOPY	93
Using COPY	95
Using BACKUP	97
Deleting Data	99
Using the MS-DOS Shell Program	99
Using HELP	100
Using MENU	102
MENU Utility Options	103
Using an AUTOEXEC.BAT File	104
Creating an AUTOEXEC.BAT File	105
Starting an Application Program	106
Using Memory Beyond 640KB	106
About EMM386.SYS	108
Chap 4-Troubleshooting	111
The Computer Won’t Start	111
The LCD Screen Is Blank	112
The Monitor Screen Is Blank	113
The Computer Locks Up	114
Diskette Problems	114
Diskette Drive Problems	115
Hard Disk Problems	116
Appendix A-DIP Switches	117
Setting the DIP Switches	117
Accessing the DIP Switches	118
Replacing the Expansion Card Cover	123
Appendix B-Installing Options	125
Connecting an External Color Monitor	125
Connecting an External Diskette Drive	127
Installing the Internal Modem	128
Installing the RAM Card	129
Connecting an External Keyboard	130
Installing an Option Card	131
Installing a Math Coprocessor	137
Appendix C-Specifications	138
Main Unit	138
Interfaces	138
Keyboard	139
Mass Storage	139
Display	139
Power Supply	140
Power Requirements	140
Physical Dimensions	140
Environmental Requirements	141
Options	141
Appendix D-System Diagnostics	142
Starting the Diagnostics Program	143
Creating a Database	143
The Main Menu Screen	145
Selecting Diagnostics Tests	147
Setting the Run Time Parameters	148
Timebound Testing	150
Continuous Testing	150
Passbound Testing	150
Error Logging	151
Executing Diagnostics Tests in Batch Mode	153
Running the Tests	153
System Board Diagnostics	154
Basic Functionality Test	154
CPU Protected Mode Test	154
Processor Speed Test	155
Coprocessor Test	155
DMA Controller Test	155
Interrupt Controller Test	156
Timer Test	156
RTC Test	157
CMOS Validity Test	157
Memory Diagnostics	158
BIOS ROM Test	159
Parity Test	159
Pattern Test	159
Walking 1’s Test	160
Walking 0’s Test	160
Address Test	160
Refresh Test	161
Hard Disk Diagnostics	161
Hard Disk Parameters	162
Hard Disk Format	165
Auto Interleave	166
Media Analysis	167
Performance Test	168
Seek Test	169
Read/Verify Test	169
Check Test Cylinder	170
Force Bad Tracks	170
Hard Disk Error Messages	171
Floppy Disk Diagnostics	172
Diskette Format	173
Drive Speed Test	173
Random R/W Test	173
Sequential R/W Test	174
Disk Change Line Test	174
Floppy Disk Error Messages	174
Keyboard Diagnostics	175
Controller Test	176
Scan/ASCII Code Test	176
Keyboard Clock Line Test	176
Keyboard Data Line Test	176
Video Diagnostics	177
Adapter Test	177
Attribute Test	177
80x25 Display Test	177
40x25 Display Test	178
320x200 Graphics Test	178
640x200 Graphics Test	178
Page Selection Test	178
Color Test	178
640x350 Graphics Test	178
640x480 Graphics Test	179
Video Error Message	179
Miscellaneous Diagnostics	179
Printer Adapter Test	179
Communication Adapter Test	180
Keyboard Scan/ASCII Codes	182
Appendix E-Using OS/2	198
Adding the Driver After OS/2 Is Installed	199
Appendix F-Using Other Reference Diskette Utilities	201
Using Microsoft Windows/386	201
Using Microsoft Windows/386	201
Using Microsoft Windows, Version 3.0	203
Using VGARAM	204
Using SCROLL	205
Glossary	206
Index	228

Match case Limit results 1 per page

This equipment generates and uses radio frequency energy and if it is not installed

and used properly, that is, in strict accordance with the manufacturer’s instructions, it

may cause interference to radio and television reception. It has been type tested and

found to comply with the limits for a Class B computing device in accordance with

the specifications in Subpart B of Part 15 of FCC rules, which are designed to provide

reasonable protection against such interference in a residential installation. However,

there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause interference to radio and television reception, which can

be determined by turning the equipment off and on, you are encouraged to try to

correct the interference by one or more of the following measures:

Reorient the receiving antenna

Relocate the computer with respect to the receiver

Move the computer away from the receiver

Plug the computer into a different outlet so that the computer and receiver are

on different branch circuits.

If necessary, consult your dealer or an experienced radio/television technician for

additional suggestions. You may find the following booklet prepared by the Federal

Communications Commission helpful:

“Television Interference Handbook”

This booklet is available from the U.S. Government Printing Office, Washington DC

20402. Stock No. 004-000-00450-7

Note: If the interference stops, it was probably caused by the computer or its

peripheral devices. To further isolate the problem:

Disconnect the peripheral devices and their input/output cables one at a time. If the

interference stops, it is caused by either the peripheral device or its I/O cable. These

devices usually require shielded I/O cables. For Epson peripheral devices, you can

obtain the proper shielded cable from your dealer. For non-Epson peripheral devices,

contact the manufacturer or dealer for assistance.

WARNING: This equipment has been certified to comply with the limits for a

Class B computer

device, pursuant to Subpart B of Part 15 of FCC Rules. Only

peripherals

(computer input/output devices, terminals, printers, etc.) certified to

comply

with the Class B limits may be attached to this computer. Operation with

noncertified peripherals is likely to result in interference to radio and TV

reception.

The

connection of a nonshielded equipment interface cable to this equipment will

invalidate the FCC Certification of this device and may cause interference levels

that exceed the limits established by the FCC for this equipment.

DOC COMPLIANCE STATEMENT FOR CANADIAN USERS

This digital apparatus does not exceed the Class B limits for radio noise emissions

from digital apparatus as set out in the radio interference regulations of the Canadian

Department of Communications.

Conformation

Les

Normes

d’Emission

Radioelectriques

Canadiennes

present

appareil

numerique

n’emet

pas

bruits

radioelectriques

depassant

les

limites

applicables

aux

appareils

numeriques

Classe

prescrites

dans

reglement

sur

brouillage

radioelectriques

edict6

par

Minis&e

des

Communications du

Canada.