Epson PowerLite 85 User's Guide - Page 129

Solving Problems with the Remote Control

Get Epson PowerLite 85 PDF manuals and user guides View all Epson PowerLite 85 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 129 highlights

Solving Problems with the Remote Control The projector doesn't respond to remote control commands. ■ The remote control's batteries may not be installed correctly or may be low on power. To change the batteries, see page 30. ■ Make sure you are within about 20 feet (6 meters) of the projector and within range of the projector's front or back sensor (approximately 30° to the left or right and 15° above or below). ■ Dim the room lights and turn off any fluorescent lights. Make sure the projector is not in direct sunlight. Strong lighting, especially fluorescent lights, may affect the projector's infrared receivers. Also, turn off any nearby equipment that emits infrared energy, such as a radiant room heater. To avoid interference, you can also turn off the projector's front or back sensor with the Remote Receiver setting (see page 94), but this may limit where you can use the remote control. ■ Make sure the projector's sensors have not been turned off with the Remote Receiver setting (see page 94). ■ If any buttons are held for longer than 30 seconds, the remote enters sleep mode. Release any button that is held to wake the remote. ■ If you're using the remote control as a wireless mouse, make sure the USB Type B setting in the Extended menu is set to Wireless Mouse (see page 101). Solving Problems 129

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
Solving Problems
129
Solving Problems with the Remote
Control
The projector doesn’t respond to remote control commands.
■
The remote control’s batteries may not be installed correctly or
may be low on power. To change the batteries, see page 30.
■
Make sure you are within about 20 feet (6 meters) of the projector
and within range of the projector’s front or back sensor
(approximately 30° to the left or right and 15° above or below).
■
Dim the room lights and turn off any fluorescent lights. Make
sure the projector is not in direct sunlight. Strong lighting,
especially fluorescent lights, may affect the projector’s infrared
receivers. Also, turn off any nearby equipment that emits infrared
energy, such as a radiant room heater. To avoid interference, you
can also turn off the projector’s front or back sensor with the
Remote Receiver
setting (see page 94), but this may limit where
you can use the remote control.
■
Make sure the projector’s sensors have not been turned off with
the
Remote Receiver
setting (see page 94).
■
If any buttons are held for longer than 30 seconds, the remote
enters sleep mode. Release any button that is held to wake the
remote.
■
If you’re using the remote control as a wireless mouse, make sure
the
USB Type B
setting in the Extended menu is set to
Wireless
Mouse
(see page 101).