GE AJCQ10ACC Owners Manual - Page 17

R_remove, Conditioner

Get GE AJCQ10ACC PDF manuals and user guides View all GE AJCQ10ACC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Installation Instructions [_]STORM WINDOW REQUIREMENTS A storm window frame will not allow the air conditioner to tilt towards the outside and will keep it from draining properly. To adjust for this, attach a piece of wood to the stool. 1/2" higher _' than & _1_ _/Wood frame _,,,_Stol F Storm " _ II window _ II frame _ II WOOD PIECES: WIDTH: 2" LENGTH: Long enough to fit inside the window frame. THICKNESS: To determine the thickness, place a piece of wood on the stool to make it 1/2" higher than the top of the storm window frame. Attach securely with nails or screws provided by the installer. r_REMOVE AIR CONDITIONER FROM CASE [] Remove all shipping pads (if present) inside the [] Remove the front grille. See the Care and air conditioner next to the compressor. Cleaning section. [] Find the locking plate located on the front left side. [] Remove the screw and the locking plate to unlock the air conditioner. (- plate _ ) _-'_ screw RemovJe [] Remove and discard the shipping screw on the back of the air conditioner to allow removal of the air conditioner from the case. Remove shipping pads (if present) [] Remove the rear grille that is taped to the back of the case. Remove the packet of screws taped to the back of the grille. While holding the grille at a 45 ° angle, insert it into the clips atthe top of the case and push the bottom in. Keep slight upward pressure on the grille until it fits flush with the bottom of the case. If attaching the grille from the outside of the case use the 2 long screws. If attaching the grille on the inside of the case use the 2 short screws. Clips screw [] Pull the bottom corners of the air conditioner and slide it out of the case. Insert the 2 long screws on the outside Insert the 2 short screws on the inside 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Installation
Instructions
[_]STORM
WINDOW
REQUIREMENTS
A storm
window
frame
will
not allow
the air
conditioner
to tilt towards
the outside
and
will
keep
it from
draining
properly.
To adjust
for
this,
attach
a piece
of wood
to the stool.
1/2" higher
_'
_/Wood
than
&
_1_
frame
_,,,_Stol
F
Storm "
_
II
window
_
II
frame
_
II
WOOD PIECES:
WIDTH:
2"
LENGTH: Long enough to fit inside the window
frame.
THICKNESS:
To determine
the thickness,
place
a
piece
of wood
on the stool
to make
it 1/2" higher
than
the top of the storm
window
frame.
Attach
securely
with
nails
or screws
provided
by
the
installer.
r_REMOVE
AIR
CONDITIONER
FROM
CASE
[]
Remove
the front
grille.
See the
Care and
Cleaning
section.
[]
Find
the locking
plate
located
on the front
left side.
[]
Remove
the screw
and
the locking
plate
to
unlock
the
air conditioner.
(-
plate
_
)
_-'_
Remove
J
screw
[]
Remove
and
discard
the shipping
screw
on the back of the air conditioner
to
allow
removal
of the air conditioner
from
the
case.
screw
[]
Pull the
bottom
corners
of the
air
conditioner
and
slide
it out
of the
case.
[]
Remove
all shipping
pads (if present)
inside
the
air conditioner
next to the compressor.
Remove
shipping
pads
(if present)
[]
Remove
the
rear grille
that
is taped
to the back
of the case.
Remove
the
packet
of screws
taped
to the back
of the grille.
While
holding
the grille
at a 45° angle,
insert
it into
the clips
atthe
top of
the case and
push the
bottom
in. Keep slight
upward
pressure
on the grille
until
it fits
flush
with
the bottom
of the case.
If attaching
the
grille
from
the
outside
of
the case use the 2
long
screws.
If attaching
the
grille
on the inside
of the
case
use the 2 short
screws.
Clips
Insert
the
2 long
screws
on
the
outside
Insert the 2 short screws
on the inside
17