Haier HMV1630DBWW HMV1630 Installation Guide - Page 10

Placement Of The Mounting Plate - microwave oven

Get Haier HMV1630DBWW PDF manuals and user guides View all Haier HMV1630DBWW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

English 1. PLACEMENT OF THE MOUNTING PLATE A. REMOVING THE MICROWAVE OVEN FROM THE CARTON/ REMOVING THE MOUNTING PLATE 1. Remove the installation instructions, filters, glass tray and the small hardware bag. Do Carton not remove the Styrofoam protecting the front of the oven. 2. Fold back all 4 carton flaps fully against Styrofoam carton sides. Then carefully roll the oven and carton over onto the top side. The oven should be resting in the Styrofoam. 3. Pull the carton up and off the oven. Screws 4. Remove and properly discard plastic bags. Mounting Plate 5. Remove the screws from the mounting plate. This plate will be used as the rear wall template and for mounting. Reinstall the screws into the holes where they were removed. B. FINDING THE WALL STUDS 1. Find the studs, using one of the following methods: A. Stud finder - a magnetic device which locates nails. OR B. Use a hammer to tap lightly across the mounting surface to find a solid sound. This will indicate a stud location. 2. After locating the stud(s), find the center by probing the wall with a small nail to find the edges of the stud. Then place a mark halfway between the edges. The center of any adjacent studs should be 16" (40.6 cm) or 24" (61 cm) from this mark. 3. Draw a line down the center of the studs. THE MICROWAVE MUST BE CONNECTED TO AT LEAST ONE WALL STUD. Wall Studs Center 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
9
English
1. PLACEMENT OF THE MOUNTING PLATE
A. REMOVING THE MICROWAVE OVEN FROM THE CARTON/
REMOVING THE MOUNTING PLATE
B. FINDING THE WALL STUDS
1. Remove the installation instructions, filters,
glass tray and the small hardware bag. Do
not remove the Styrofoam protecting the
front of the oven.
2. Fold back all 4 carton flaps fully against
carton sides. Then carefully roll the oven
and carton over onto the top side. The oven
should be resting in the Styrofoam.
3. Pull the carton up and off the oven.
4. Remove and properly discard plastic bags.
5. Remove the screws from the mounting
plate. This plate will be used as the rear
wall template and for mounting. Reinstall
the screws into the holes where they were
removed.
1. Find the studs, using one of the following
methods:
A. Stud finder – a magnetic device which
locates nails.
OR
B. Use a hammer to tap lightly across the
mounting surface to find a solid sound.
This will indicate a stud location.
2. After locating the stud(s), find the center by
probing the wall with a small nail to find the
edges of the stud. Then place a mark
halfway between the edges. The center of
any adjacent studs should be 16” (40.6 cm)
or 24” (61 cm) from this mark.
3. Draw a line down the center of the studs.
THE MICROWAVE MUST BE CONNECTED TO
AT LEAST ONE WALL STUD.
Carton
Styrofoam
Mounting
Plate
Screws
Wall
Studs
Center