Haier HMV1630DBWW HMV1630 Installation Guide - Page 19

B3. Attach The Mounting Plate To The Wall, B4. Use Top Cabinet Template For Preparation Of, Top

Get Haier HMV1630DBWW PDF manuals and user guides View all Haier HMV1630DBWW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Engglliisshh B3. ATTACH THE MOUNTING PLATE TO THE WALL Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud. 1. Remove the toggle wings from the bolts. 2. Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to 3⁄4" (19 mm) onto each bolt. TO USE TOGGLE BOLTS: 3. Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate. Mounting Plate NOTE: Before tightening toggle bolts and wood screw, make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet. CAUTION: Be careful to avoid pinching fingers between the back of the mounting plate and thewall. Spacing for Toggles More Than Wall Thickness Toggle Wings Toggle Bolt Wall Bolt End 4. Tighten all bolts. Pull the plate away from the wall to help tighten the bolts. B4. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws, a hole large enough for the power cord to fit through. t Read the instructions on the TOP CABINET TEMPLATE. t Tape it underneath the top cabinet. t Drill the holes, following the instructions on the TOP CABINET TEMPLATE. CAUTION: Wear safety goggles when drilling holes in the cabinet bottom. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
18
English
Attach the plate to the wall using toggle
bolts. At least one wood screw must be
used to attach the plate to a wall stud.
Remove the toggle wings from the bolts.
1.
Insert the bolts into the mounting plate
2.
through the holes designated to go into
drywall and reattach the toggle wings to
3⁄4” (19 mm) onto each bolt.
TO USE TOGGLE BOLTS:
Place the mounting plate against the
3.
wall and insert the toggle wings into the
holes in the wall to mount the plate.
NOTE: Before tightening toggle bolts and wood screw,
make sure the tabs on the mounting plate touch the
bottom of the cabinet when pushed flush against the wall
and that the plate is properly centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers
between the back of the mounting plate and thewall.
Tighten all bolts. Pull the plate away
4.
from the wall to help tighten the bolts.
B3. ATTACH THE MOUNTING PLATE TO THE WALL
Wall
Mounting
Plate
Spacing for Toggles
More Than Wall
Thickness
Bolt End
Toggle
Bolt
Toggle Wings
You need to drill holes for the top support
screws, a hole large enough for the power
cord to fit through.
Read the instructions on the TOP
CABINET TEMPLATE.
Tape it underneath the top cabinet.
Drill the holes, following the instructions
on the TOP CABINET TEMPLATE.
B4. USE TOP CABINET TEMPLATE FOR PREPARATION OF
TOP CABINET
CAUTION:
Wear safety goggles when drilling holes in the cabinet bottom.