Haier HMV1630DBWW HMV1630 Installation Guide - Page 15

Caution, A2. Use Top Cabinet Template For Preparation Of, Top Cabinet, A3. Adapting Microwave Blower

Get Haier HMV1630DBWW PDF manuals and user guides View all Haier HMV1630DBWW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

English A2. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor. t3FBEUIFJOTUSVDUJPOTPOUIF501  CABINET TEMPLATE. t5BQFJUVOEFSOFBUIUIFUPQDBCJOFU t%SJMMUIFIPMFT GPMMPXJOHUIFJOTUSVDUJPOT on the TOP CABINET TEMPLATE. CAUTION: Wear safety goggles when drilling holes in the cabinet bottom. A3. ADAPTING MICROWAVE BLOWER FOR OUTSIDE TOP EXHAUST 1. Place the microwave in its upright position,with the top of the unit facing up. Remove the screw that holds the blower plate to the microwave. Remove and save the screw holding the blower motor to the microwave. Blower Plate Back of Microwave Blower Moto Screw 2. Carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower unit. End A End B Back of Microwave 3. Roll the blower unit 90° so that fan blade openings are facing out the top of the microwave. Before Rotation After Rotation Back of Microwave Back of Microwave 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
14
English
You need to drill holes for the top support
screws, a hole large enough for the power
cord to fit through, and a cutout large
enough for the exhaust adaptor.
CABINET TEMPLATE.
on the TOP CABINET TEMPLATE.
CAUTION:
Wear safety goggles when drilling holes in the cabinet bottom.
Place the microwave in its upright
1.
position,with the top of the unit facing up.
Remove the screw that holds the blower
plate to the microwave. Remove and
save the screw holding the blower motor
to the microwave.
Carefully pull out the blower unit. The
2.
wires will extend far enough to allow
you to adjust the blower unit.
Roll the blower unit 90° so that fan
3.
blade openings are facing out the top
of the microwave.
A2. USE TOP CABINET TEMPLATE FOR PREPARATION OF
TOP CABINET
A3. ADAPTING MICROWAVE BLOWER FOR OUTSIDE
TOP EXHAUST
Blower Plate
Blower Moto
Screw
Back of
Microwave
End B
End A
Back of
Microwave
Back of
Microwave
Before Rotation
After Rotation
Back of
Microwave