Haier HMV1630DBWW HMV1630 Installation Guide - Page 20

B5. Adapting Microwave Blower For Outside Back, Exhaust

Get Haier HMV1630DBWW PDF manuals and user guides View all Haier HMV1630DBWW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

English B5. ADAPTING MICROWAVE BLOWER FOR OUTSIDE BACK EXHAUST 1. Remove and save screw that holds blower motor to microwave. Blower Motor Back of Microwave 2. Carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower unit. Before: Fan Blade Openings Facing Forward Blower Motor Screw End B 3. Roll the blower unit 90° Before Rotation After Rotation End A 4. Rotate blower unit counterclockwise 180°. Before Rotation After Rotation Back of Microwave Back of Microwave Back of Microwave Back of Microwave 5. Gently remove the wires from the grooves. Reroute the wires through grooves on other side of the blower unit. Before Rerouting After Rerouting 6. Roll the blower unit 90° so that fan blade openings are facing out the back of the microwave. Before Rolling After Rolling Wires Routed Through Right Side Wires Routed Through Left Side Back of Microwave Back of Microwave 7. Place the blower unit back into the opening. AFTER: Fan Blade Openings Facing Back CAUTION: Do not pull or stretch the End A blower unit wiring. Make sure the wires are not pinched, and that they are End B properly secured. NOTE: The blower unit exhaust openings should match exhaust openings on rear of microwave oven. 8. Secure the blower unit to the microwave with the original screw. 9. Replace the blower plate in the same position as before with the screw. Make sure the screw is tight. 19 Blower Plate Back of Microwave Blower Motor Screw

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
English
B5. ADAPTING MICROWAVE BLOWER FOR OUTSIDE BACK
EXHAUST
Remove and save screw that holds
1.
blower motor to microwave.
Carefully pull out the blower unit. The
2.
wires will extend far enough to
allow you to adjust the blower unit.
Roll the blower unit 90°
3.
5. Gently remove the wires from the
grooves. Reroute the wires through
grooves on other side of the blower unit.
7. Place the blower unit back into the
opening.
CAUTION: Do not pull or stretch the
blower unit wiring. Make sure the wires
are not pinched, and that they are
properly secured.
NOTE: The blower unit exhaust
openings should match exhaust
openings on rear of microwave oven.
8. Secure the blower unit to the
microwave with the original screw.
9. Replace the blower plate in the
same position as before with the
screw. Make sure the screw is tight.
4. Rotate blower unit counterclockwise 180°.
6. Roll the blower unit 90° so that fan blade
openings are facing out the back of the
microwave.
Back of
Microwave
Blower Motor
Blower Motor
Screw
Blower Plate
Blower Motor
Screw
Back of
Microwave
End B
End A
Forward
Openings Facing
Before: Fan Blade
Back of
Microwave
Before Rotation
After Rotation
Back of
Microwave
Before Rotation
After Rotation
Back of
Microwave
Back of
Microwave
Before Rerouting
After Rerouting
Wires Routed Through Right Side
Wires Routed Through Left Side
Before Rolling
After Rolling
Back of
Microwave
Back of
Microwave
AFTER: Fan Blade
Openings Facing Back
End A
End B
19