Haier HMV1630DBWW HMV1630 Installation Guide - Page 12

Caution

Get Haier HMV1630DBWW PDF manuals and user guides View all Haier HMV1630DBWW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

English Hole A Centerline Notches Draw a Vertical Line on Wall from Center of Top Cabinet Hole B Hole C Area E Hole D CAUTION: Wear gloves to avoid cutting fingers on sharp edges. D. ALIGNING THE WALL PLATE 1. Draw a vertical line on the wall at the center of the 30" (76.2 cm) wide space. 2. Use the mounting plate as the template for the rear wall. Place the mounting plate on the wall, making sure that the tabs are touching the bottom of the cabinet or the level line drawn in Step C for cabinets with front overhang. Line up the notch and centerline on the bottom of the mounting plate to the centerline on the wall. 3. While holding the mounting plate with one hand, draw circles on the wall at holes A, B, C and D (see illustration above/actual plate marked with arrows). Four holes must be used for mounting. NOTE: If neither C nor D is in a stud, find a stud somewhere in area E and draw a fifth circle to line up with the stud. It is important to use at least one wood screw mounted firmly in a stud to support the weight of the microwave. Set the mounting plate aside. 4. Drill holes on the circles. If there is a stud, drill a 3⁄16" hole for wood screws. For holes that don't line up with a stud, drill a 5⁄8" hole for toggle bolts. NOTE: DO NOT MOUNT THE PLATE AT THIS TIME. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
CAUTION:
Wear gloves to avoid cutting fingers on sharp edges.
11
English
D. ALIGNING THE WALL PLATE
Draw a vertical line on the wall at the center of the 30” (76.2 cm) wide space.
1.
Use the mounting plate
2.
as the template
for the rear wall. Place the mounting
plate on the wall, making sure that the tabs are
touching the bottom of the
cabinet or the level line drawn in Step C for cabinets with front overhang.
Line up the notch and centerline on the bottom of the mounting plate to the
centerline on the wall.
While holding the mounting plate with one hand, draw circles on the wall
3.
at holes A, B, C and D (see illustration above/actual plate marked with
arrows). Four holes must be used for mounting.
NOTE:
If neither C nor D is in a stud, find a stud somewhere in area E and
draw a fifth circle to line up with the stud. It is important to use at least one
wood screw mounted firmly in a stud to support the weight of the microwave.
Set the mounting plate aside.
Drill holes on the circles. If there is a stud, drill a 3⁄16” hole for wood screws.
4.
For holes that don’t line up with a stud, drill a 5⁄8” hole for toggle bolts.
NOTE: DO NOT MOUNT THE PLATE AT THIS TIME.
Draw a Vertical
Line on Wall
from Center of
Top Cabinet
Area E
Hole A
Hole B
Hole D
Hole C
Centerline
Notches