Haier HMV1630DBWW HMV1630 Installation Guide - Page 14

A. Outside Top Exhaust

Get Haier HMV1630DBWW PDF manuals and user guides View all Haier HMV1630DBWW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

English A. OUTSIDE TOP EXHAUST (VERTICAL DUCT) INSTALLATION OVERVIEW A1. Attach Mounting Plate to Wall A2. Prepare Top Cabinet A3. Adapting Microwave Blower for Outside Top Exhaust A4. Check Damper Operation A5. Mount Microwave Oven A6. Adjust Exhaust Adaptor A7. Connect Ductwork IMPORTANT NOTES: t Make sure the screws for the blower motor and blower plate are securely tightened when they are reinstalled. This will help to prevent excessive vibration t Make sure the motor wiring has been properly routed and secured, and that the wires are not pinched. A1. ATTACH THE MOUNTING PLATE TO THE WALL Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud. 1. Remove the toggle wings from the bolts. 2. Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to 3⁄4" (19 mm) onto each bolt. TO USE TOGGLE BOLTS: 3. Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate. NOTE: Before tightening toggle bolts and wood screw, Mounting make sure the tabs on the mounting plate touch the Plate bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet. CAUTION: Be careful to avoid pinching fingers between the back of the mounting plate and thewall. 4. Tighten all bolts. Pull the plate away from the wall to help tighten the bolts. Spacing for Toggles More Than Wall Thickness Toggle Wings Toggle Bolt Wall Bolt End 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
13
English
INSTALLATION OVERVIEW
A1. Attach Mounting Plate to Wall
A2. Prepare Top Cabinet
A3. Adapting Microwave Blower
for Outside Top Exhaust
A4. Check Damper Operation
A5. Mount Microwave Oven
A6. Adjust Exhaust Adaptor
A7. Connect Ductwork
Attach the plate to the wall using toggle
bolts. At least one wood screw must be
used to attach the plate to a wall stud.
Remove the toggle wings from the bolts.
1.
Insert the bolts into the mounting plate
2.
through the holes designated to go into
drywall and reattach the toggle wings to
3⁄4” (19 mm) onto each bolt.
TO USE TOGGLE BOLTS:
Place the mounting plate against the
3.
wall and insert the toggle wings into the
holes in the wall to mount the plate.
NOTE: Before tightening toggle bolts and wood screw,
make sure the tabs on the mounting plate touch the
bottom of the cabinet when pushed flush against the wall
and that the plate is properly centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers
between the back of the mounting plate and thewall.
Tighten all bolts. Pull the plate away
4.
from the wall to help tighten the bolts.
A1. ATTACH THE MOUNTING PLATE TO THE WALL
IMPORTANT NOTES:
Make sure the screws for the blower motor and blower plate are securely
tightened when they are reinstalled. This will help to prevent excessive vibration
Make sure the motor wiring has been properly routed and secured, and that
the wires are not pinched.
A. OUTSIDE TOP EXHAUST
(VERTICAL DUCT)
Wall
Mounting
Plate
Spacing for Toggles
More Than Wall
Thickness
Bolt End
Toggle
Bolt
Toggle Wings