Hayward Aqua Connect Aqua Connect Operations Manual - Page 10

TEMPERATURES AND POOL/SPA/SPILLOVER STATUS • Air Temperature - This temperature is always displayed. • Solar Temperature - The solar temperature will not be displayed unless solar is enabled. The solar temperature displayed is the temperature of the water in the solar collectors. When the filter is Off, the solar temperature becomes "n/a". • Pool/Spa/Spillover Status - This status is most important if you have a Pool & Spa standard configuration (a pool and a spa sharing a single pump, possibly including spillover from the spa to the pool). For a pool only system, the status will always be pool. For a Pool & Spa Dual Equipment configuration, the status will be pool unless spillover is present and active. For a Pool & Spa Std configuration, the status will be Pool if the filter is connected to the pool, Spa if the filter is connected to the spa, and Spillover if spillover is present and active. HEATER SETTINGS AND WATER TEMPS At the top right of the Dashboard is the "Heater Settings, Water Temps" section. This section displays water temperature, filter status, and heater setup and status. Heater Settings, Water Temps is subdivided into 3 fields: Heater Status, Pool and Spa. Heater Status There are 3 possible heat sources supported by the Pro Logic pool controller; two conventional heaters and Solar heater. If a heat source is enabled in the Pro Logic Configuration Menu, then a status LED for that heat source will appear in the Heater Status field, next to text that identifies the LED. If none of the 3 heat sources are enabled, then the Heater Status field will not appear at all. The Dashboard shown in Figure 3 has three heat sources, none of which are currently active. When an LED is on (green), then the heat source is active. When an LED is off (black), then the heat source is inactive. Note that the heat sources are color coded: light blue corresponds to Heater1, red corresponds to Heater2, and yellow corresponds to Solar. Heater1, Heater2, and Solar are the default names for the 3 heat sources. It is possible to rename the Heater1 and Heater2 buttons on the Remote Control page. When these buttons are renamed on the Remote Control page, the new names will also appear in the Heater Status field. Pool The Pool section gives the status of the pool. In a Pool Only or Pool & Spa Dual Equipment configuration, the Pool section will ALWAYS be present. In a Pool & Spa Standard configuration, the Pool section will be present when the filter is connected to the pool, or if spillover is possible and the system is in spillover mode. The status of the pool filter pump is also displayed - High, Low, Cooldown, or Off. The water temperature can only be read accurately when there is water flowing past the sensor. So if the filter is in any state other than Off, an accurate water temperature is available and will be displayed. When the filter is Off, the last valid water temperature will continue to be displayed for a few hours, but the water temperature value will eventually switch to "n/a" and remain there until the filter turns back on. The water temperature is displayed 2 ways: Numerically and also using a needle on a half round dial. When the numerical water temperature display is "n/a", the needle will disappear. The set points of every heater that can be connected to the pool are also shown. A color coded triangle (same color code as for Heater Status) appears on the dial and color coded text appears above the dial. Set points are always valid (even when the filter is off). 8 Hayward® - Remote Pool Control Website Terms of Use This website (the "Site") is published and maintained by Hayward® Industries, Inc. (the "Company"), primarily to allow owners of Hayward® swimming pool controllers and the pool service companies that are allowed to service those swimming pools the ability to remotely monitor and control their swimming pools (the "Service"). When you access, browse, or use this Site or take advantage of the Service you accept and agree to, without limitation or qualification, the terms and conditions set forth below. Your Right to Use the Site and the Service Aqua Connect™ Home Network (the "Gateway") is a gateway device that allows the Hayward pool controller to connect to the Site. There are two possible scenarios that will be considered here. In the first, the owner of the pool (the "Pool Owner") and the owner of the Gateway (the "Gateway Owner") are the same individual. In the second the Pool Owner and the Gateway Owner are different. A common example of the later scenario is when a pool service provider installs a Gateway that they own on a pool that they do not own as part of a service contract or agreement with the Pool Owner. In addition to the Pool Owner and the Gateway Owner, there may be other individuals who are given access to the Site by permission of either the Pool Owner or the Gateway Owner (the "Registered Guests"). These individuals may be, but are not limited to, friends or relatives of the Pool Owner or employees of the Gateway Owner. This Terms of Use Agreement is for ALL users of the Site; the Pool Owner, the Gateway Owner, and all Registered Guests. The Site and the Service are intended only for the Gateway Owner, the Pool Owner, and any Registered Guests that either the Gateway Owner or the Pool Owner choose to allow. Upon the creation of your login account the Company will issue you a username and allow you to select a password to access the Service. You are not authorized to access the Service through use of any username other than the one issued to you by the Company upon registration. The Gateway Owner agrees to (i) provide accurate, current and complete information as may be prompted by any registration forms for the Service ("Registration Information"); (ii) maintain and promptly update the Registration Information and any other information they provide to the Company, to keep it accurate, current and complete; (iii) maintain the confidentiality of your username and password to access the Service; and (iv) accept full responsibility for all consequences of all actions initiated and all conduct that occurs under your username and password. The Gateway Owner also accepts full responsibility for all consequences of all actions initiated and conducted that occur under any username that is a sub-account of the Gateway Owners login account. These would be Pool Owners and Registered Guests to whom the Gateway Owner has extended access privileges. Your authorization to access and use the Service with your username and password extends only while: 1) You are a Gateway Owner: you have a current subscription to the Service for this Gateway device. 2) You are a Pool Owner who has contracted with a Gateway Owner: you have a current contract with the Gateway Owner (pool service provider) who has installed the Gateway device on your pool AND the Gateway Owner has a current subscription to the Service for this Gateway device. 3) You are a Registered Guest: You have the current permission of both the Gateway Owner and the Pool Owner AND the Gateway Owner has a current subscription to the Service for this Gateway device. In all usage cases your authorization to access and use the Service with your username and password extends only while you conform to the Terms of Use contained in this document. If the subscription for the Gateway device expires, then ALL ACCESS to that Gateway device, for all parties that have been granted access, ceases. The cessation of service can only be ended by the renewal of the subscription for the Gateway device. 21