HP 285 Maintenance and Service Guide - Page 39

Installing a 9.5 mm slim optical drive, onto the drive.

Get HP 285 PDF manuals and user guides View all HP 285 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Installing a 9.5 mm slim optical drive 1. Prepare the computer for disassembly (Preparation for disassembly on page 17). 2. Remove the access panel (Access panel on page 18). 3. If you are installing a slim optical drive in a bay covered by a bezel blank, remove the front bezel and then remove the bezel blank. See Front bezel on page 19 for more information. 4. Follow the instructions for removing the optical drive if one was installed. Refer to Removing a 9.5 mm slim optical drive on page 30. 5. Align the small pin on the release latch with the small hole on the side of the drive and press the latch firmly onto the drive. 6. Slide the optical drive through the front of the chassis (1) all the way into the bay so that the green latch locks onto the chassis frame (2). Drives 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
Installing a 9.5 mm slim optical drive
1.
Prepare the computer for disassembly (
Preparation for disassembly
on page
17
).
2.
Remove the access panel (
Access panel
on page
18
).
3.
If you are installing a slim optical drive in a bay covered by a bezel blank, remove the front bezel and
then remove the bezel blank. See
Front bezel
on page
19
for more information.
4.
Follow the instructions for removing the optical drive if one was installed. Refer to
Removing a 9.5 mm
slim optical drive
on page
30
.
5.
Align the small pin on the release latch with the small hole on the side of the drive and press the latch
firmly
onto the drive.
6.
Slide the optical drive through the front of the chassis
(1)
all the way into the bay so that the green latch
locks onto the chassis frame
(2)
.
Drives
31