HP 285 Maintenance and Service Guide - Page 44

cable to one of the SATA connectors labeled SATA1 or SATA2

Get HP 285 PDF manuals and user guides View all HP 285 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

6. Connect the power cable (1) and data cable (2) to the rear of the hard drive. 7. If installing a new drive, connect the opposite end of the data cable to the appropriate system board connector. NOTE: You must connect the primary hard drive data cable to the dark blue connector labeled SATA0 to avoid any hard drive performance problems. If you are adding a second hard drive, connect the data cable to one of the SATA connectors labeled SATA1 or SATA2. 8. Replace the computer access panel. 9. Reconnect the power cord and any external devices, and then turn on the computer. 10. Lock any security devices that were disengaged when the access panel was removed. 36 Chapter 4 Removal and replacement procedures - Microtower (MT) chassis

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
6.
Connect the power cable
(1)
and data cable
(2)
to the rear of the hard drive.
7.
If installing a new drive, connect the opposite end of the data cable to the appropriate system board
connector.
NOTE:
You must connect the primary hard drive data cable to the dark blue connector labeled SATA0 to
avoid any hard drive performance problems. If you are adding a second hard drive, connect the data
cable to one of the SATA connectors labeled SATA1 or SATA2.
8.
Replace the computer access panel.
9.
Reconnect the power cord and any external devices, and then turn on the computer.
10.
Lock any security devices that were disengaged when the access panel was removed.
36
Chapter 4
Removal and replacement procedures – Microtower (MT) chassis