HP 9200C HP 9200c Digital Sender - User Guide - Page 17

Understanding digital-sender status, Sleep mode - digital sender troubleshooting

Get HP 9200C - Digital Sender PDF manuals and user guides
UPC - 829160458878
View all HP 9200C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Understanding digital-sender status The digital sender has two buttons and three lights to indicate and control the digital-sender status. To interpret the control-panel lights, see the follow table. For information about troubleshooting digital-sender problems, see Problem solving. Digital Sender status indications Element Status indication SLEEP button START button When in Sleep mode, the green LED on the button is lit. Push this button to enter or end Sleep mode. The Start LED is green when the device is ready to scan. It is amber if an error exists. Ready LED Data LED The Ready LED is on when the device is online and able to send data, or flashing when attempting to pause a job. The Data LED is on if the job has been paused. It flashes when the device is transmitting data. Attention LED If the red Attention LED is lit or flashing, the device has encountered an error. Sleep mode After 60 minutes of inactivity, the device automatically enters Sleep mode. In Sleep mode, many of the digital sender's processes are shut down to conserve energy. The user can press any button on the control panel to bring the device out of Sleep mode. The device takes approximately 30 seconds to warm up and return to Ready mode. The settings for Sleep mode can be changed by using the Configure Device menu on the control panel. See the HP 9200C Digital Sender Support Guide for instructions about using this menu. ENWW Control-panel features 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Understanding digital-sender status
The digital sender has two buttons and three lights to indicate and control the digital-sender
status. To interpret the control-panel lights, see the follow table. For information about
troubleshooting digital-sender problems, see
Problem
solving
.
Digital Sender status indications
Element
Status indication
S
LEEP
button
When in Sleep mode, the green LED on the button is lit. Push this
button to enter or end Sleep mode.
S
TART
button
The Start LED is green when the device is ready to scan. It is amber
if an error exists.
Ready
LED
The Ready LED is on when the device is online and able to send
data, or flashing when attempting to pause a job.
Data
LED
The Data LED is on if the job has been paused. It flashes when the
device is transmitting data.
Attention
LED
If the red Attention LED is lit or flashing, the device has encountered
an error.
Sleep mode
After 60 minutes of inactivity, the device automatically enters Sleep mode. In Sleep mode,
many of the digital sender's processes are shut down to conserve energy. The user can
press any button on the control panel to bring the device out of Sleep mode. The device
takes approximately 30 seconds to warm up and return to Ready mode. The settings for
Sleep mode can be changed by using the
Configure Device
menu on the control panel.
See the
HP 9200C Digital Sender Support Guide
for instructions about using this menu.
ENWW
Control-panel features
11