HP 9200C HP 9200c Digital Sender - User Guide - Page 47

Embedded I/O Buffer Overflow, Embedded I/O Bad Transmission

Get HP 9200C - Digital Sender PDF manuals and user guides
UPC - 829160458878
View all HP 9200C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Error message 11.xx Internal Clock Error 20 Insufficient Memory 22 EIO Buffer Overflow 22 Embedded I/O Buffer Overflow 30.1.yy Scan Failure 40 EIO Bad Transmission 40 Embedded I/O Bad Transmission 52.xy Error 57.xx Error 64 ERROR alternates with To continue turn off then on Explanation or action needed The internal clock is not working. The digital sender can still send, but you are prompted to set the date and time whenever the device is turned off and then turned on. Contact your system administrator. The the scanned document contains more data than can fit in the device's available memory. Press START to send the available data (some data might be lost), and then try to make the scan job smaller. Too much data was sent to the EIO card. An incorrect communications protocol might be in use. Turn the device off and then on. If this message persists, contact your system administrator. Too much data was sent to the embedded HP Jetdirect network interface. Turn the device off and then on. Try to send the job again. If this message persists, contact your system administrator. An error has occurred in the flatbed scanner. Turn the device off and then on. A 30.18 Scan Failure message might indicate that the scanner head is locked. Verify that the scanner lock is in the unlocked position. (See Digital-sender parts for the location of the scanner lock.) If the error persists, contact your system administrator. The connection between the device and the EIO card has failed. Press START to clear the error and continue sending. The connection with the embedded HP Jetdirect network interface has failed. Turn the device off and then on. The scanner has encountered an error. Turn the device off and then on. If this message persists, contact your system administrator. The fan motor has encountered an error. Turn the device off and then on. If this message persists, contact your system administrator. A scan buffer error occurred. Turn the device off and then on. If this message persists, contact your system administrator. ENWW Understanding control-panel error messages 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Error message
Explanation or action needed
11.xx Internal Clock Error
The internal clock is not working. The digital
sender can still send, but you are prompted to
set the date and time whenever the device is
turned off and then turned on.
Contact your system administrator.
20 Insufficient Memory
The the scanned document contains more data
than can fit in the device's available memory.
Press
S
TART
to send the available data (some
data might be lost), and then try to make the
scan job smaller.
22 EIO Buffer Overflow
Too much data was sent to the EIO card. An
incorrect communications protocol might be in
use. Turn the device off and then on. If this
message persists, contact your system
administrator.
22 Embedded I/O Buffer Overflow
Too much data was sent to the embedded
HP Jetdirect network interface. Turn the device
off and then on. Try to send the job again. If this
message persists, contact your system
administrator.
30.1.yy Scan Failure
An error has occurred in the flatbed scanner.
Turn the device off and then on.
A
30.18 Scan Failure
message might indicate
that the scanner head is locked. Verify that the
scanner lock is in the unlocked position. (See
Digital-sender
parts
for the location of the
scanner lock.) If the error persists, contact your
system administrator.
40 EIO Bad Transmission
The connection between the device and the EIO
card has failed. Press
S
TART
to clear the error
and continue sending.
40 Embedded I/O Bad Transmission
The connection with the embedded HP Jetdirect
network interface has failed. Turn the device off
and then on.
52.xy Error
The scanner has encountered an error. Turn the
device off and then on. If this message persists,
contact your system administrator.
57.xx Error
The fan motor has encountered an error. Turn
the device off and then on. If this message
persists, contact your system administrator.
64 ERROR
alternates with
To continue turn off then on
A scan buffer error occurred. Turn the device off
and then on. If this message persists, contact
your system administrator.
ENWW
Understanding control-panel error messages
41