HP Dragonfly 13.5 Maintenance and Service Guide - Page 58

Remove the Phillips M2.0 × 3.9 screw

Get HP Dragonfly 13.5 PDF manuals and user guides View all HP Dragonfly 13.5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Before removing the solid-state drive, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 48). 2. Remove the bottom cover (see Bottom cover on page 48). 3. Disconnect the battery cable from the system board (see Battery on page 50). Remove the solid-state drive: 1. Remove the solid-state drive shield (1). The solid-state drive shield is included in the Bracket Kit, spare part number N08562-001. 2. Remove the Phillips M2.0 × 3.9 screw (2) that secures the solid-state drive to the computer. 3. Remove the solid-state drive (3) by sliding it out of the socket at an upward angle. 4. Thoroughly clean the thermal material from the surfaces of the solid-state drive and the solid-state drive shield each time the solid-state drive shield is removed. Replacement thermal material is included with the solid-state drive shield spare part kit. The following illustration shows the replacement thermal material locations. A thermal pad is used on the solid-state drive (1) and on the solid-state drive shield area (2) that services it. 52 Chapter 5 Removal and replacement procedures for authorized service provider parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
Before removing the solid-state drive, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
48
).
2.
Remove the bottom cover (see
Bottom cover
on page
48
).
3.
Disconnect the battery cable from the system board (see
Battery
on page
50
).
Remove the solid-state drive:
1.
Remove the solid-state drive shield
(1)
.
The solid-state drive shield is included in the Bracket Kit, spare part number N08562-001.
2.
Remove the Phillips M2.0 × 3.9 screw
(2)
that secures the solid-state drive to the computer.
3.
Remove the solid-state drive
(3)
by sliding it out of the socket at an upward angle.
4.
Thoroughly clean the thermal material from the surfaces of the solid-state drive and the solid-state
drive shield each time the solid-state drive shield is removed. Replacement thermal material
is included with the solid-state drive shield spare part kit. The following illustration shows the
replacement thermal material locations.
A thermal pad is used on the solid-state drive
(1)
and on the solid-state drive shield area
(2)
that
services it.
52
Chapter 5
Removal and replacement procedures for authorized service provider parts