HP Dragonfly 13.5 Maintenance and Service Guide - Page 61

Display assembly, remove the interposer board by lifting

Get HP Dragonfly 13.5 PDF manuals and user guides View all HP Dragonfly 13.5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Table 5-5 Connector board descriptions and part numbers (continued) Description In slate blue finish Spare part number N16841-001 Before removing the connector board, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 48). 2. Remove the bottom cover (see Bottom cover on page 48). 3. Disconnect the battery cable from the system board (see Battery on page 50). Remove the connector board: 1. Remove the four Phillips M2.0 × 3.9 screws (1) that secure the connector board to the computer. 2. Remove the connector board (2) and disconnect it from the interposer board. 3. If it is necessary to replace the interposer board (3), remove the interposer board by lifting it straight up. The interposer board is available using spare part number N11562-001. To install the connector board and interposer board, reverse this procedure. Display assembly To remove and disassemble the display assembly, use these procedures and illustrations. Table 5-6 Display assembly descriptions and part numbers Description In natural silver finish: 34.3 cm (13.5 in), LCD, WUXGA (1920 × 1200), nantiglare, UWVA, TOP display panel; typical brightness: 1000 nits Spare part number N51331-001 Display assembly 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
Table 5-5
Connector board descriptions and part numbers
(continued)
Description
Spare part number
In slate blue finish
N16841-001
Before removing the connector board, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
48
).
2.
Remove the bottom cover (see
Bottom cover
on page
48
).
3.
Disconnect the battery cable from the system board (see
Battery
on page
50
).
Remove the connector board:
1.
Remove the four Phillips M2.0 × 3.9 screws
(1)
that secure the connector board to the computer.
2.
Remove the connector board
(2)
and disconnect it from the interposer board.
3.
If it is necessary to replace the interposer board
(3)
, remove the interposer board by lifting it
straight up.
The interposer board is available using spare part number N11562-001.
To install the connector board and interposer board, reverse this procedure.
Display assembly
To remove and disassemble the display assembly, use these procedures and illustrations.
Table 5-6
Display assembly descriptions and part numbers
Description
Spare part number
In natural silver finish:
34.3 cm (13.5 in), LCD, WUXGA (1920 × 1200), nantiglare, UWVA, TOP display panel; typical brightness:
1000 nits
N51331-001
Display assembly
55