HP ENVY 14-u000 ENVY 14 Notebook PC Maintenance and Service Guide - Page 45

Display subcomponents (bezel, webcamera, panel), IMPORTANT

Get HP ENVY 14-u000 PDF manuals and user guides View all HP ENVY 14-u000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Display subcomponents (bezel, webcamera, panel) This section describes removing display subcomponents that do not require that you remove the entire display assembly from the computer. You can remove the display bezel, webcam/microphone module, and display panel while the display assembly is still attached to the computer. To remove the remaining display subcomponents, you must remove the entire display assembly from the computer. See Display assembly on page 66 for more information about removing the display assembly in its entirety. Description Display bezel for use in models without a touch screen (includes screws) Raw display panel, 35.56 cm (14 in), WLED, HD, BrightView, flat for use in models without a touch screen Raw display panel, 35.56 cm (14 in), FHD, WLED, SVA, Antiglare slim for use in models without a touch screen Webcamera/microphone module for use in models without a touch screen Webcamera/microphone module for use in touch screen models Spare part number 767365-001 763566-001 767373-001 762521-001 762545-001 IMPORTANT: Make special note of each screw and screw lock size and location during removal and replacement Before removing the display panel, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the battery (see Battery on page 31). Remove the panel: If it is necessary to replace the display bezel: 1. Remove the plastic screw covers (1) and the two Phillips M2.5×3.0 screws (2) that secure the display bezel to the display assembly. 2. If it is necessary to replace the display bezel or any of the display assembly subcomponents: a. Flex the inside edges of the top edge (3), the left and right sides (4), and the bottom edge (5) of the display bezel until the bezel disengages from the display enclosure. Component replacement procedures 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
Display subcomponents (bezel, webcamera, panel)
This section describes removing display subcomponents that do not require that you remove the entire
display assembly from the computer. You can remove the display bezel, webcam/microphone module, and
display panel while the display assembly is still attached to the computer.
To remove the remaining display subcomponents, you must remove the entire display assembly from the
computer. See
Display assembly
on page
66
for more information about removing the display assembly in
its entirety.
Description
Spare part number
Display bezel for use in models without a touch screen (includes screws)
767365-001
Raw display panel,
35.56 cm
(14 in), WLED, HD, BrightView, flat for use in models without a touch screen
763566-001
Raw display panel,
35.56 cm
(14 in), FHD, WLED, SVA, Antiglare slim for use in models without a touch
screen
767373-001
Webcamera/microphone module for use in models without a touch screen
762521-001
Webcamera/microphone module for use in touch screen models
762545-001
IMPORTANT:
Make special note of each screw and screw lock size and location during removal
and replacement
Before removing the display panel, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see
Battery
on page
31
).
Remove the panel:
If it is necessary to replace the display bezel:
1.
Remove the plastic screw covers
(1)
and the two Phillips M2.5×3.0 screws
(2)
that secure the display
bezel to the display assembly.
2.
If it is necessary to replace the display bezel or any of the display assembly subcomponents:
a.
Flex the inside edges of the top edge
(3)
, the left and right sides
(4)
, and the bottom edge
(5)
of
the display bezel until the bezel disengages from the display enclosure.
Component replacement procedures
35