HP ENVY 14-u000 ENVY 14 Notebook PC Maintenance and Service Guide - Page 67

Memory module, Remove the memory module, located on the bottom of the system board

Get HP ENVY 14-u000 PDF manuals and user guides View all HP ENVY 14-u000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Memory module Description 4 GB memory module (PC3, 12800, 1600 MHz) 8 GB memory module (PC3, 12800, 1600 MHz) Spare part number 691740-005 693374-005 NOTE: Before adding memory modules, make sure the computer has the most recent BIOS version, and update the BIOS if needed. For Windows operating systems, see Updating the BIOS on page 74. Before removing a memory module, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the battery (see Battery on page 31), and then remove the following components: a. Optical drive (see Optical drive on page 32) b. Top cover (see Top cover on page 39) c. Power connector cable (see Power connector cable on page 63) d. System board (see System board on page 52) Remove the memory module, located on the bottom of the system board: NOTE: Note the location of the memory module you are removing. If you are replacing it, install the new memory module in the same slot. 1. Spread the two retaining tabs (1) on each side of the memory module slot to release the memory module. (The memory module tilts up.) Component replacement procedures 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
Memory module
Description
Spare part number
4 GB memory module (PC3, 12800, 1600 MHz)
691740-005
8 GB memory module (PC3, 12800, 1600 MHz)
693374-005
NOTE:
Before adding memory modules, make sure the computer has the most recent BIOS version, and
update the BIOS if needed. For Windows operating systems, see
Updating the BIOS
on page
74
.
Before removing a memory module, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see
Battery
on page
31
), and then remove the following components:
a.
Optical drive (see
Optical drive
on page
32
)
b.
Top cover (see
Top cover
on page
39
)
c.
Power connector cable (see
Power connector cable
on page
63
)
d.
System board (see
System board
on page
52
)
Remove the memory module, located on the bottom of the system board:
NOTE:
Note the location of the memory module you are removing. If you are replacing it, install the new
memory module in the same slot.
1.
Spread the two retaining tabs
(1)
on each side of the memory module slot to release
the memory module. (The memory module tilts up.)
Component replacement procedures
57