HP ENVY m6-n000 ENVY m6 Notebook PC Maintenance and Service Guide - Page 48

Display assembly, Release the ZIF connector to which the display panel cable is attached

Get HP ENVY m6-n000 PDF manuals and user guides View all HP ENVY m6-n000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Reverse this procedure to install the base enclosure. Display assembly Description 15.6-in, AntiGlare, FHD, LED, TouchScreen display assembly for use on all computer models 15.6-in, AntiGlare, HD, LED, TouchScreen display assembly for use on all computer models Spare part number 788475-001 788474-001 To remove the display assembly and access the display assembly subcomponents, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the battery (see Battery on page 29). 5. Disconnect the wireless antenna cables from the WLAN module (see WLAN module on page 30). 6. Remove the hard drive (see Hard drive on page 32). 7. Remove the base enclosure (see Base enclosure on page 38). Remove the display assembly: 1. Release the wireless antenna cables from the retention clips built into the left rear speaker (1), connector board (2), and top cover (3). 2. Release the wireless antenna cables from the retention clips (4) built into the subwoofer. 3. Release the ZIF connector to which the display panel cable is attached, and then disconnect the display panel cable (5) from the system board. 4. Disconnect the the webcam/microphone module cable (6) from the system board. 5. Release the display panel cable and the webcam/microphone module cable from the clips and routing channel built into the right rear speaker (7). 40 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
Reverse this procedure to install the base enclosure.
Display assembly
Description
Spare part number
15.6-in, AntiGlare, FHD, LED, TouchScreen display assembly for use on all computer models
788475-001
15.6-in, AntiGlare, HD, LED, TouchScreen display assembly for use on all computer models
788474-001
To remove the display assembly and access the display assembly subcomponents, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see
Battery
on page
29
).
5.
Disconnect the wireless antenna cables from the WLAN module (see
WLAN module
on page
30
).
6.
Remove the hard drive (see
Hard drive
on page
32
).
7.
Remove the base enclosure (see
Base enclosure
on page
38
).
Remove the display assembly:
1.
Release the wireless antenna cables from the retention clips built into the left rear speaker
(1)
,
connector board
(2)
, and top cover
(3)
.
2.
Release the wireless antenna cables from the retention clips
(4)
built into the subwoofer.
3.
Release the ZIF connector to which the display panel cable is attached, and then disconnect the display
panel cable
(5)
from the system board.
4.
Disconnect the the webcam/microphone module cable
(6)
from the system board.
5.
Release the display panel cable and the webcam/microphone module cable from the clips and routing
channel built into the right rear speaker
(7)
.
40
Chapter 6
Removal and replacement procedures for Authorized Service Provider parts