HP ENVY m6-n000 ENVY m6 Notebook PC Maintenance and Service Guide - Page 60

Power connector cable, Hard drive see

Get HP ENVY m6-n000 PDF manuals and user guides View all HP ENVY m6-n000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

6. Lift the right side of the connector board (2) until it rests at an angle. 7. Remove the connector board (3) by sliding it up and to the right at an angle. Reverse this procedure to install the connector board. Power connector cable Description Power connector cable Spare part number 720537-001 Before removing the power connector cable, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the battery (see Battery on page 29), and then remove the following components: a. Service cover (see WLAN module on page 30) b. Hard drive (see Hard drive on page 32) c. Base enclosure (see Base enclosure on page 38) Remove the power connector cable: 1. Disconnect the power cable (1) from the system board. 2. Release the power connector cable from the clips (2) built into the keyboard shield. 52 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
6.
Lift the right side of the connector board
(2)
until it rests at an angle.
7.
Remove the connector board
(3)
by sliding it up and to the right at an angle.
Reverse this procedure to install the connector board.
Power connector cable
Description
Spare part number
Power connector cable
720537-001
Before removing the power connector cable, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see
Battery
on page
29
), and then remove the following components:
a.
Service cover (see
WLAN module
on page
30
)
b.
Hard drive (see
Hard drive
on page
32
)
c.
Base enclosure (see
Base enclosure
on page
38
)
Remove the power connector cable:
1.
Disconnect the power cable
(1)
from the system board.
2.
Release the power connector cable from the clips
(2)
built into the keyboard shield.
52
Chapter 6
Removal and replacement procedures for Authorized Service Provider parts