HP ENVY m6-n000 ENVY m6 Notebook PC Maintenance and Service Guide - Page 52

Remove the system board, Disconnect the following cables from the system board

Get HP ENVY m6-n000 PDF manuals and user guides View all HP ENVY m6-n000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Before removing the system board, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the battery (see Battery on page 29), and then remove the following components: a. Service cover (see WLAN module on page 30) b. Hard drive (see Hard drive on page 32) c. Base enclosure (see Base enclosure on page 38) d. Display assembly (see Display assembly on page 40) e. Fan (see Fan on page 42) NOTE: When replacing the system board, be sure that the following components are removed from the defective system board and installed on the replacement system board: ● Memory module (see Memory module on page 33) ● Heat sink (see Heat sink on page 47) ● Processor (see Processor on page 49) Remove the system board: 1. Disconnect the following cables from the system board: (1) Connector board cable (2) Connector board ribbon cable (3) Power connector cable (4) Display panel cable (5) Webcam/microphone module cable (6) Wireless antenna cables 44 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
Before removing the system board, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see
Battery
on page
29
), and then remove the following components:
a.
Service cover (see
WLAN module
on page
30
)
b.
Hard drive (see
Hard drive
on page
32
)
c.
Base enclosure (see
Base enclosure
on page
38
)
d.
Display assembly (see
Display assembly
on page
40
)
e.
Fan (see
Fan
on page
42
)
NOTE:
When replacing the system board, be sure that the following components are removed from the
defective system board and installed on the replacement system board:
●
Memory module (see
Memory module
on page
33
)
●
Heat sink (see
Heat sink
on page
47
)
●
Processor (see
Processor
on page
49
)
Remove the system board:
1.
Disconnect the following cables from the system board:
(1)
Connector board cable
(2)
Connector board ribbon cable
(3)
Power connector cable
(4)
Display panel cable
(5)
Webcam/microphone module cable
(6)
Wireless antenna cables
44
Chapter 6
Removal and replacement procedures for Authorized Service Provider parts