HP G62-400 HP G62 Notebook PC - Maintenance and Service Guide - Page 85

Remove the four Phillips PM2.5×4.0, Remove the following cables from the system board

Get HP G62-400 - Notebook PC PDF manuals and user guides View all HP G62-400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

Remove the following cables from the system board: ● Power connector cable (see Power connector on page 67) ● USB board cable (see USB board on page 65) Remove the system board: 1. Turn the computer upright with the right side toward you. 2. Remove the four Phillips PM2.5×4.0 (1) screws that secure the system board to the computer. 3. Grasp the right edge (2) of the system board. 4. Lift the system board (3), and pull it away from the base enclosure at an angle. Reverse this procedure to install the system board. Component replacement procedures 75

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
Remove the following cables from the system board:
●
Power connector cable (see
Power connector
on page
67
)
●
USB board cable (see
USB board
on page
65
)
Remove the system board:
1.
Turn the computer upright with the right side toward you.
2.
Remove the four Phillips PM2.5×4.0
(1)
screws that secure the system board to the computer.
3.
Grasp the right edge
(2)
of the system board.
4.
Lift the system board
(3)
, and pull it away from the base enclosure at an angle.
Reverse this procedure to install the system board.
Component replacement procedures
75