HP Integrity Superdome SX1000 HP Insight Manager WBEM Provider Events Referenc - Page 83
been detected in the Instruction or Data Cache Memory I-Cache or D-Cache.
View all HP Integrity Superdome SX1000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 83 highlights
Event ID Event Severity Event Description 10822 Warning Over-temperature condition detected on a processor. Probable Cause: The processor temperature is above the operating range. The processor's performance is throttled by the firmware to reduce the temperature Recommended Action: The firmware has already taken necessary action. Once the temperature comes down, the firmware will restore the processor's performance to normal WBEM EventID: 4543. WBEM ProviderName: FPL_IndicationProvider 10823 Warning Cache errors detected on a processor. Probable Cause: Threshold parity errors have been detected in the Instruction or Data Cache Memory (I-Cache or D-Cache). The operating system has recovered from the errors, but this is an abnormally high failure rate Recommended Action: Contact your HP support representative to check the processor WBEM EventID: 4544. WBEM ProviderName: FPL_IndicationProvider 10824 Warning Corrected errors detected in the cache portion of the memory for a processor module. Probable Cause: Threshold corrected platform errors have been detected in the cache portion of the memory for the processor module. The operating system has recovered from the errors, but this is an abnormally high failure rate Recommended Action: Contact your HP support representative to check the processor WBEM EventID: 4545. WBEM ProviderName: FPL_IndicationProvider 10825 Warning Corrected errors detected on the system bus for a processor module. Probable Cause: Threshold corrected platform errors have been detected on the system bus for the processor module. The operating system has recovered from the errors, but this is an abnormally high failure rate Recommended Action: Contact your HP support representative to check the processor module or the system bus for the processor if an excessive number of these errors are generated WBEM EventID: 4546. WBEM ProviderName: FPL_IndicationProvider 10826 Warning Corrected errors detected on the processor bus for a processor module. Probable Cause: Threshold corrected platform errors have been detected on the processor bus for the processor module. The operating system has recovered from the errors, but this is an abnormally high failure rate Recommended Action: Contact your HP support representative to check the processor module or the system bus for the processor if an excessive number of these errors are generated WBEM EventID: 4547. WBEM ProviderName: FPL_IndicationProvider 10827 Warning Corrected errors detected in the tag portion of the memory for a processor module. Probable Cause: Threshold corrected platform errors have been detected in the tag portion of the memory for the processor module. The operating system has recovered from the errors, but this is an abnormally high failure rate. Recommended Action: Contact your HP support representative to check the processor module if an excessive number of these errors are generated WBEM EventID: 4548. WBEM ProviderName: FPL_IndicationProvider 10830 Warning fPars-mode EFI variable is set to enable fPars operation but no fPars are actually enabled to boot. So the server boots in hard partition mode. Probable Cause: fPars-mode EFI variable is set to enable fPars operation but no fPars are actually enabled to boot. So the server boots in hard partition mode. This is a configuration usage problem, possibly a user error such as might occur if a previously bootable config was made unbootable by setting the enabled fPar existence variables, e.g., 'fPar0', 'fPar1', ... 'fParN' to 0x00 (disabled) and then rebooting Recommended Action: Use the configuration tool released with the OS to disable fPars mode or to configure and enable bootable fPars. WBEM EventID: 4700. WBEM ProviderName: FPL_IndicationProvider 10832 Warning An fPar was directed to reset using the ESIT DirectedfParResetAndMigrate() service but the target (recipient) fPar of the resources is in a state that cannot receive ownership of these resources. Probable Cause: An fPar was directed to reset using the ESIT DirectedfParResetAndMigrate() service but the target (recipient) fPar of the resources is in a state that cannot receive ownership of these resources. Recommended Action: Use the configuration tool released with the OS to correctly assign these resources to an fPar and reset that fPar so they will be claimed. WBEM EventID: 4701. WBEM ProviderName: FPL_IndicationProvider Platform Events 83