HP LaserJet Enterprise M806 User Guide 1 - Page 65

Install or replace a stapler/stacker or stapler/stacker with hole punch accessory for the HP Color L

Get HP LaserJet Enterprise M806 PDF manuals and user guides View all HP LaserJet Enterprise M806 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Install or replace a stapler/stacker or stapler/stacker with hole punch accessory for the HP Color LaserJet Enterprise M855 and HP Color LaserJet Enterprise flow MFP M880 ● Introduction ● Before you begin ● Required tools ● Step one: remove the stapler/stacker ● Step two: Unpack the optional or replacement stapler/stacker ● Step three: Install the optional or replacement stapler/stacker ● Step four: Parts return ● Step five: Configure the default hole punch location ● Step six: Configure the default staple location Introduction The following information provides the procedures to install or replace a stapler/stacker accessory for the HP Color LaserJet Enterprise M855 and HP Color LaserJet Enterprise Flow MFP M880. NOTE: To see a short video demonstrating this procedure, click here. Before you begin Use the table below to identify the correct accessory part number for your accessory, and then go to www.hp.com/buy/parts to order the accessory. Table 2-3 Stapler/stacker accessory part numbers A2W80A A2W82A Stapler/stacker accessory with installation instructions Stapler/stacker with 2/4 hole punch accessory with installation instructions To replace an existing stapler/stacker, go to Step one: remove the stapler/stacker on page 57. To install a new stapler/stacker, go to Step two: Unpack the optional or replacement stapler/stacker on page 58. Required tools No special tools are required to install this accessory. Step one: remove the stapler/stacker 1. Turn off the product, and then disconnect the power cord. CAUTION: To avoid damage to the product, turn the product off, wait five seconds, and then remove the power cord before attempting to service the product. ENWW Install or replace a stapler/stacker or stapler/stacker with hole punch accessory for the HP Color LaserJet 57 Enterprise M855 and HP Color LaserJet Enterprise flow MFP M880

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
Install or replace a stapler/stacker or stapler/stacker with hole
punch accessory for the HP Color LaserJet Enterprise M855 and
HP Color LaserJet Enterprise flow MFP M880
●
Introduction
●
Before you begin
●
Required tools
●
Step one: remove the stapler/stacker
●
Step two: Unpack the optional or replacement stapler/stacker
●
Step three: Install the optional or replacement stapler/stacker
●
Step four: Parts return
●
Step five: Configure the default hole punch location
●
Step six: Configure the default staple location
Introduction
The following information provides the procedures to install or replace a stapler/stacker accessory for the
HP Color LaserJet Enterprise M855 and HP Color LaserJet Enterprise Flow MFP M880.
NOTE:
To see a short video demonstrating this procedure, click
here
.
Before you begin
Use the table below to identify the correct accessory part number for your accessory, and then go to
www.hp.com/
buy/parts
to order the accessory.
Table 2-3
Stapler/stacker accessory part numbers
A2W80A
Stapler/stacker accessory with installation instructions
A2W82A
Stapler/stacker with 2/4 hole punch accessory with installation instructions
To replace an existing stapler/stacker, go to
Step one: remove the stapler/stacker
on page
57
.
To install a new stapler/stacker, go to
Step two: Unpack the optional or replacement stapler/stacker
on page
58
.
Required tools
No special tools are required to install this accessory.
Step one: remove the stapler/stacker
1.
Turn off the product, and then disconnect the power cord.
CAUTION:
To avoid damage to the product, turn the product off, wait five seconds, and then remove
the power cord before attempting to service the product.
ENWW
Install or replace a stapler/stacker or stapler/stacker with hole punch accessory for the HP Color LaserJet
Enterprise M855 and HP Color LaserJet Enterprise flow MFP M880
57