HP NetServer LXr Pro8 HP Netserver Mass Storage Upgrade Guide - Page 12

Step 2, Unlock and Remove Front Bezel, Step 3, Remove Cover 1 and Cover Plate

Get HP NetServer LXr Pro8 PDF manuals and user guides View all HP NetServer LXr Pro8 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Chapter 2 Installation 3. Turn off power to the HP NetServer. 4. Disconnect the AC power cords and all external cables from the HP NetServer. WARNING Before removing the cover, always disconnect the power cord(s) and unplug telephone cables. Disconnect telephone cables to avoid exposure to shock hazard from telephone ringing voltages. Disconnect the power cord(s) to avoid exposure to high energy levels that may cause burns when parts are short-circuited by metal objects such as tools or jewelry. Note that the power switch does NOT turn off the standby power. Disconnect the power cord(s) to turn off standby power. If the backlight on the front panel LCD is still on, standby power is still on. Step 2: Unlock and Remove Front Bezel To unlock and remove the front bezel, refer to the guides listed below that apply to your HP NetServer configuration: • HP NetServer LH 3000/3000r Installation Guide • HP NetServer LH 6000/6000r Installation Guide • The Installation Guide for Compaq® 4000/7000 Racks for your HP NetServer Step 3: Remove Cover 1 and Cover Plate WARNING If the HP NetServer is installed in a rack, extend the anti-tip foot or attach the anti-tip feature before extending the HP NetServer from the rack. Also lower the leveler feet of the rack to improve stability and to prevent the rack from rolling. Failure to use the anti-tip foot or feature and the leveler feet could result in serious injury. 1. If the HP NetServer is installed in a rack, extend the HP NetServer from the rack. Refer to your HP NetServer installation guide for instructions. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Chapter 2
Installation
8
3.
Turn off power to the HP NetServer.
4.
Disconnect the AC power cords and all external cables from the
HP NetServer.
WARNING
Before removing the cover, always disconnect the power
cord(s) and unplug telephone cables. Disconnect telephone
cables to avoid exposure to shock hazard from telephone
ringing voltages. Disconnect the power cord(s) to avoid
exposure to high energy levels that may cause burns when
parts are short-circuited by metal objects such as tools or
jewelry.
Note that the power switch does NOT turn off the standby
power. Disconnect the power cord(s) to turn off standby
power. If the backlight on the front panel LCD is still on,
standby power is still on.
Step 2:
Unlock and Remove Front Bezel
To unlock and remove the front bezel, refer to the guides listed below that apply
to your HP NetServer configuration:
•
HP NetServer LH 3000/3000r Installation Guide
•
HP NetServer LH 6000/6000r Installation Guide
•
The
Installation Guide for Compaq
®
4000/7000 Racks
for your HP
NetServer
Step 3:
Remove Cover 1 and Cover Plate
WARNING
If the HP NetServer is installed in a rack, extend the anti-tip
foot or attach the anti-tip feature before extending the
HP NetServer from the rack. Also lower the leveler feet of the
rack to improve stability and to prevent the rack from rolling.
Failure to use the anti-tip foot or feature and the leveler feet
could result in serious injury.
1.
If the HP NetServer is installed in a rack, extend the HP NetServer from
the rack. Refer to your HP NetServer installation guide for instructions.