HP NetServer LXr Pro8 HP Netserver Mass Storage Upgrade Guide - Page 38

The Embedded LAN and SCSI Settings submenu is displayed. If

Get HP NetServer LXr Pro8 PDF manuals and user guides View all HP NetServer LXr Pro8 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Chapter 3 Configure Mass Storage 11. The Embedded LAN and SCSI Settings submenu is displayed. If HP NetRAID/LVD SCSI is not already highlighted, use the up and down arrows to highlight it. Read the values in the brackets to determine whether LVD SCSI is enabled. ◊ Enable LVD SCSI indicates that LVD SCSI is enabled and HP NetRAID is disabled. This is the correct setting for non-RAID operation of the mass storage cages connected to SCSI A and B on the I/O baseboard. ◊ Enable HP NetRAID indicates that HP NetRAID is enabled to provide RAID operation of the mass storage cages connected to SCSI A and B on the I/O baseboard. This is the default value. CAUTION If your HP NetServer was previously operating in RAID mode (Enable HP NetRAID), changing to non-RAID mode (Enable LVD SCSI) could cause data loss. Be sure your data is backed up before you change to non-RAID mode. If the value is not Enable LVD SCSI, use the +/- keys to change it to Enable LVD SCSI. This change will take effect when the HP NetServer restarts. Exit Setup Utility 12. Press the F10 function key to save and exit. 13. In the Setup Confirmation dialog box, press Enter to answer "Yes" to the question, "Save configuration changes and exit now?" The HP NetServer will restart. 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Chapter 3
Configure Mass Storage
34
11.
The Embedded LAN and SCSI Settings submenu is displayed. If
HP NetRAID/LVD SCSI
is not already highlighted, use the up and down
arrows to highlight it.
Read the values in the brackets to determine whether LVD SCSI is
enabled.
◊
Enable LVD SCSI
indicates that LVD SCSI is enabled and
HP NetRAID is disabled. This is the correct setting for non-RAID
operation of the mass storage cages connected to SCSI A and B on the
I/O baseboard.
◊
Enable HP NetRAID
indicates that HP NetRAID is enabled to
provide RAID operation of the mass storage cages connected to
SCSI A and B on the I/O baseboard. This is the default value.
CAUTION
If your HP NetServer was previously operating in RAID mode
(Enable HP NetRAID), changing to non-RAID mode (Enable
LVD SCSI) could cause data loss. Be sure your data is backed
up before you change to non-RAID mode.
If the value is not
Enable LVD SCSI
, use the +/- keys to change it to
Enable LVD SCSI
. This change will take effect when the HP NetServer
restarts.
Exit Setup Utility
12.
Press the F10 function key to save and exit.
13.
In the Setup Confirmation dialog box, press Enter to answer "Yes" to the
question, "Save configuration changes and exit now?" The HP NetServer
will restart.