HP OMEN 15-5000 Maintenance and Service Guide - Page 46

Power connector cable

Get HP OMEN 15-5000 PDF manuals and user guides View all HP OMEN 15-5000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Power connector cable Component Power connector cable (includes cable, bracket, and screws) Spare part number 788599-001 Before replacing the power connector cable, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the bottom cover (see Bottom cover on page 25). 5. Remove the battery (see Battery on page 33). 6. Remove the heat sink and fans (see Heat sink and fans on page 31). 7. Remove the system board (see System board on page 36). Remove the power connector cable: 1. Remove the two Phillips PM2.0×3.0 screws (1) that secure the bracket over the power connector. 2. Lift the bracket from atop the power connector (2). 3. Remove the power connector and cable (3) from the computer. Reverse this procedure to install the power connector cable. 40 Chapter 5 Removal and replacement procedures for Authorized Service Provider parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
Power connector cable
Component
Spare part number
Power connector cable (includes cable, bracket, and screws)
788599-001
Before replacing the power connector cable, follow these steps:
1.
Turn
off
the computer. If you are unsure whether the computer is
off
or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the bottom cover (see
Bottom cover
on page
25
).
5.
Remove the battery (see
Battery
on page
33
).
6.
Remove the heat sink and fans (see
Heat sink and fans
on page
31
).
7.
Remove the system board (see
System board
on page
36
).
Remove the power connector cable:
1.
Remove the two Phillips PM2.0×3.0 screws
(1)
that secure the bracket over the power connector.
2.
Lift the bracket from atop the power connector
(2)
.
3.
Remove the power connector and cable
(3)
from the computer.
Reverse this procedure to install the power connector cable.
40
Chapter 5
Removal and replacement procedures for Authorized Service Provider parts