HP Pavilion TouchSmart 14-f000 HP Pavillion Sleekbook 14 Maintenance and Servi - Page 49

hard drive., Remove the four Phillips PM3.0×3.73 screws

Get HP Pavilion TouchSmart 14-f000 PDF manuals and user guides View all HP Pavilion TouchSmart 14-f000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

5. Remove the keyboard (see Keyboard on page 31). 6. Remove the top cover (see Top cover on page 33). Remove the hard drive: 1. Lift up on the right side of the hard drive (1) until the hard drive rests at an angle. 2. Slide the hard drive (2) to the right until it disconnects from the hard drive connector (3). 3. Remove the hard drive. 4. If it is necessary to disassemble the hard drive, perform the following steps: a. Position the hard drive with the connector toward you. b. Remove the four Phillips PM3.0×3.73 screws (1) that secure the hard drive bracket to the hard drive. c. Remove the hard drive bracket (2) from the hard drive. The hard drive bracket, hard drive connector cable, and screws are available in the Hard Drive Hardware Kit, spare part number 725626-001. Component replacement procedures 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
5.
Remove the keyboard (see
Keyboard
on page
31
).
6.
Remove the top cover (see
Top cover
on page
33
).
Remove the hard drive:
1.
Lift up on the right side of the hard drive
(1)
until the hard drive rests at an angle.
2.
Slide the hard drive
(2)
to the right until it disconnects from the hard drive connector
(3)
.
3.
Remove the hard drive.
4.
If it is necessary to disassemble the hard drive, perform the following steps:
a.
Position the hard drive with the connector toward you.
b.
Remove the four Phillips PM3.0×3.73 screws
(1)
that secure the hard drive bracket to the
hard drive.
c.
Remove the hard drive bracket
(2)
from the hard drive.
The hard drive bracket, hard drive connector cable, and screws are available in the Hard
Drive Hardware Kit, spare part number 725626-001.
Component replacement procedures
39