HP ProDesk 480 G7 PCI Micro Maintenance and Service Guide - Page 34

Optical drive cage

Page 34 highlights

4. Swing the front bezel (3) down and away from the system chassis. 5. Remove the front bezel. To install the front bezel, reverse the removal procedure. Optical drive cage To remove the optical drive cage, use these procedures. The optical drive cage is located next to the heat sink. The drive cage is secured with three slotted Torx screws. Before removing the optical drive cage, follow these steps: 1. Prepare the computer for disassembly (Preparation for disassembly on page 23). 2. Remove the access panel (Access panel on page 23). 3. Remove the optical drive (Optical drive on page 24). 4. Remove the front bezel (Front bezel on page 25). Remove the optical drive cage: 1. Release the 2.5 inch hard drive power cable and 2.5 inch hard drive data cable from the retention clip (1) built into the optical drive cage. 26 Chapter 4 Removal and replacement procedures ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134

4.
Swing the front bezel
(3)
down and away from the system chassis.
5.
Remove the front bezel.
To install the front bezel, reverse the removal procedure.
Optical drive cage
To remove the optical drive cage, use these procedures. The optical drive cage is located next to the heat sink.
The drive cage is secured with three slotted Torx screws.
Before removing the optical drive cage, follow these steps:
1.
Prepare the computer for disassembly (
Preparation for disassembly
on page
23
).
2.
Remove the access panel (
Access panel
on page
23
).
3.
Remove the optical drive (
Optical drive
on page
24
).
4.
Remove the front bezel (
Front bezel
on page
25
).
Remove the optical drive cage:
1.
Release the 2.5 inch hard drive power cable and 2.5 inch hard drive data cable from the retention clip
(1)
built into the optical drive cage.
26
Chapter 4
Removal and replacement procedures
ENWW