HP Spectre 13-v100 Maintenance and Service Guide - Page 36

Solid-state drive, Remove the Phillips PM1.0×2.5 screw

Get HP Spectre 13-v100 PDF manuals and user guides View all HP Spectre 13-v100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Solid-state drive Description 1-TB, 2280, PCIe, 3×4, NVMe, 3LC, 1 side, SN solid-state drive 512-GB, M.2, 2280, NVMe solid-state drive supporting TLC 256-GB, M.2, 2280, NVMe solid-state drive supporting TLC Spare part number 908359-002 855609-001 855608-001 Before removing the solid-state drive, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the bottom cover (see Bottom cover on page 26). 5. Disconnect the battery cable from the system board (see Battery on page 28). Remove the solid-state drive: 1. Remove the Phillips PM1.0×2.5 screw (1) that secures the bracket to the computer. 2. Remove the bracket (2). 3. Slide the solid-state drive away from the connector to remove the drive (3). Reverse this procedure to install the solid-state drive. 30 Chapter 5 Removal and replacement procedures for Authorized Service Provider parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
Solid-state drive
Description
Spare part number
1-TB, 2280, PCIe, 3×4, NVMe, 3LC, 1 side, SN solid-state drive
908359-002
512-GB, M.2, 2280, NVMe solid-state drive supporting TLC
855609-001
256-GB, M.2, 2280, NVMe solid-state drive supporting TLC
855608-001
Before removing the solid-state drive, follow these steps:
1.
Turn
off
the computer. If you are unsure whether the computer is
off
or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the bottom cover (see
Bottom cover
on page
26
).
5.
Disconnect the battery cable from the system board (see
Battery
on page
28
).
Remove the solid-state drive:
1.
Remove the Phillips PM1.0×2.5 screw
(1)
that secures the bracket to the computer.
2.
Remove the bracket
(2)
.
3.
Slide the solid-state drive away from the connector to remove the drive
(3)
.
Reverse this procedure to install the solid-state drive.
30
Chapter 5
Removal and replacement procedures for Authorized Service Provider parts