HP Spectre 13-v100 Maintenance and Service Guide - Page 41

Fan, Remove the two Phillips PM2.0×3.0 screws

Get HP Spectre 13-v100 PDF manuals and user guides View all HP Spectre 13-v100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Fan Description Fans (includes left and right fans) Spare part number 855629-001 Before removing the fans, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the bottom cover (see Bottom cover on page 26). 5. Remove the battery (see Battery on page 28). Remove the fans: 1. Disconnect the left fan cables (1) from the system board. 2. Remove the two Phillips PM2.0×3.0 screws (2) that secure the left fan to the computer. 3. Lift the front edge of the left fan until it rests at an angle (approximately 45 degrees), and then remove the left fan (3). NOTE: You may need to route the left fan cable under the WLAN antenna cables. 4. Disconnect the right fan cables (1) from the system board. 5. Remove the two Phillips PM2.0×3.0 screws (2) that secure the right fan to the computer. Component replacement procedures 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
Fan
Description
Spare part number
Fans (includes left and right fans)
855629-001
Before removing the fans, follow these steps:
1.
Turn
off
the computer. If you are unsure whether the computer is
off
or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the bottom cover (see
Bottom cover
on page
26
).
5.
Remove the battery (see
Battery
on page
28
).
Remove the fans:
1.
Disconnect the left fan cables
(1)
from the system board.
2.
Remove the two Phillips PM2.0×3.0 screws
(2)
that secure the left fan to the computer.
3.
Lift the front edge of the left fan until it rests at an angle (approximately 45 degrees), and then remove
the left fan
(3)
.
NOTE:
You may need to route the left fan cable under the WLAN antenna cables.
4.
Disconnect the right fan cables
(1)
from the system board.
5.
Remove the two Phillips PM2.0×3.0 screws
(2)
that secure the right fan to the computer.
Component replacement procedures
35