HP StorageWorks 1510i HP StorageWorks 1510i Modular Smart Array maintenance an - Page 40

Removing or installing a 2-Port Ethernet iSCSI blank, Before you begin

Get HP StorageWorks 1510i - Modular Smart Array PDF manuals and user guides View all HP StorageWorks 1510i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Removing or installing a 2-Port Ethernet iSCSI blank Before you begin CAUTION: • Before removing a component or blank from an operational device, make sure that you have the replacement part or blank available. Removing a component or blank impacts the airflow pattern and cooling ability of the device. Allow approximately 30 seconds before installing the new or replacement component to ensure that configuration data about the removed component is cleared from the system registry, but, to avoid possible overheating, insert the new or replacement component within one or two minutes. If the internal temperature exceeds acceptable limits, the device may overheat and automatically shut down or restart. • Parts can be damaged by electrostatic discharge. Use proper anti-static protection. Removing a 2-Port Ethernet iSCSI blank Lift the port-colored module latch (1) and pull the module out of the chassis (2). Installing a 2-Port Ethernet iSCSI blank Slide the blank into the MSA chassis bay until the blank clicks into place. newpage pi 40 Customer replaceable components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Removing or installing a 2-Port Ethernet iSCSI blank
Before you begin
CAUTION:
•
Before removing a component or blank from an operational device, make sure that you have the
replacement part or blank available. Removing a component or blank impacts the air
fl
ow pattern
and cooling ability of the device. Allow approximately 30 seconds before installing the new or
replacement component to ensure that con
fi
guration data about the removed component is cleared
from the system registry, but, to avoid possible overheating, insert the new or replacement component
within one or two minutes. If the internal temperature exceeds acceptable limits, the device may
overheat and automatically shut down or restart.
•
Parts can be damaged by electrostatic discharge. Use proper anti-static protection.
Removing a 2-Port Ethernet iSCSI blank
Lift the port-colored module latch (
1
) and pull the module out of the chassis (
2
).
Installing a 2-Port Ethernet iSCSI blank
Slide the blank into the MSA chassis bay until the blank clicks into place.
newpage pi
40
Customer replaceable components